Subaru B9 TRIBECA WX 2007 Скачать руководство пользователя страница 716

Страница: 716 / 861

OD(diag)-1

Subaru Select Monitor

OCCUPANT DETECTION SYSTEM (DIAGNOSTICS)

10) During the system calibration process, if the

«Re-zeroing is unsuccessful See service manual

Press OK to END» is displayed, turn the ignition

switch to OFF once and turn it to ON again, and

then read the DTC of airbag system. <Ref. to

AB(diag)-32, OPERATION, Subaru Select Moni-

tor.>

When DTC is input, fix the fault and then perform

the system calibration. When DTC is not input,

check the seat and vehicle status and then perform

the system calibration again. <Ref. to OD(diag)-17,

SYSTEM CALIBRATION (REZEROING), OPERA-

TION, Subaru Select Monitor.>
NOTE:

When the re-zeroing is unsuccessful, there could

be occupant detection system failure or improper

seat and vehicle status. When the airbag warning

light illuminates, read the DTC of airbag system,

and perform the diagnosis referring to “List of Diag-

nostic Trouble Code.” <Ref. to AB(diag)-32, OPER-

ATION, Subaru Select Monitor.> <Ref. to AB(diag)-

47, LIST, List of Diagnostic Trouble Code (DTC).>

B: INSPECTION

1. COMMUNICATION FOR INITIALIZING

IMPOSSIBLE

DETECTING CONDITION:

Defective harness connector

TROUBLE SYMPTOM:

Communication is impossible between the airbag

control module and the Subaru Select Monitor.

Refer to “Initial Communication Impossible” in the

DTC of the airbag system (diagnosis). <Ref. to

AB(diag)-34, COMMUNICATION FOR INITIALIZ-

ING IMPOSSIBLE, INSPECTION, Subaru Select

Monitor.>

2. WITHOUT DTC

DETECTING CONDITION:

• Defective combination meter

• Open circuit of harness

TROUBLE SYMPTOM:

• Airbag warning light remains on.

• “NO TROUBLE CODE” will be displayed on the

Subaru Select Monitor.

For detailed operation procedure, refer to “Airbag

Warning Light Failure”. <Ref. to AB(diag)-42, Air-

bag Warning Light Failure.>
NOTE:

When the airbag warning light is OFF and “NO

TROUBLE CODE” is displayed on Subaru Select

Monitor, the system is in normal condition.

asieps_tobira.book 18 ページ２０１２年２月１０日　金曜日　午後３時２６分

Содержание B9 TRIBECA WX 2007






























































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание B9 TRIBECA WX 2007

Отзывы:

Похожие инструкции для B9 TRIBECA WX 2007

Бренды по названию

Популярные бренды

Subaru B9 TRIBECA WX 2007, Руководство пользователя

Результаты поиска

Содержание B9 TRIBECA WX 2007

Отзывы:

Похожие инструкции для B9 TRIBECA WX 2007

Бренды по названию

Популярные бренды