Subaru B9 TRIBECA WX 2007 Скачать руководство пользователя страница 763 | Manualshive

Страница: 763 / 861

background image

SE-21

Power Seat System

SEATS

6. Power Seat System

A: REMOVAL

CAUTION:

When it is necessary to remove the front seat,

disconnect the ground cable from battery and

wait for 20 seconds before disconnecting the

side airbag module harness connector.

1. POWER SEAT SWITCH

1) Detach the connectors and remove the seat side

cover outside. <Ref. to SE-8, DISASSEMBLY,

Front Seat.>

2) Remove the screws to remove the power seat

switch assembly.

NOTE:

Perform the same procedure when removing the

memory switch of memory-equipped seat.

2. MEMORY MODULE (MEMORY-

EQUIPPED SEAT)

1) Lift the seat cushion by operating the switch.

2) Remove the front seat from the vehicle.

3) Remove the nut and then remove the memory

module.

B: INSTALLATION

Install in the reverse order of removal.
NOTE:

• For the memory-equipped seat, always perform

the initialize operation after the installation. <Ref. to

SE-34, ADJUSTMENT, Power Seat System.>

• Check the following items after replacing the

memory-equipped seat or the memory module.

1. Memory feature is restored after turning the

ignition switch to ON and shifting to P range.

2. Memory feature is not restored after turning

the ignition switch to ON and shifting to other

than P range.

C: INSPECTION

1. WIRING DIAGRAM

• Driver’s side (without memory) <Ref. to WI-88,

DRIVER’S SEAT (WITH MEMORY), WIRING DIA-

GRAM, Power Seat System.>

• Driver’s side (memory-equipped) <Ref. to WI-87,

DRIVER’S SEAT (WITHOUT MEMORY), WIRING

DIAGRAM, Power Seat System.>

• Passenger’s side <Ref. to WI-89, PASSEN-

GER’S SIDE, WIRING DIAGRAM, Power Seat

System.>

2. TROUBLE SYMPTOM

• Driver’s seat (without memory)

SE-00686

SE-00687

Symptom

Criteria

All function fails to operate.
<Ref. to SE-23, ALL FUNC-
TION FAILS TO OPERATE.
(DRIVER’S SEAT, WITH-
OUT MEMORY), INSPEC-
TION, Power Seat System.>

• Power seat switch
• Power seat harness
• Body harness

A part of function does not
operate.
<Ref. to SE-24, SOME OF
THE MOTOR DO NOT
OPERATE. (DRIVER’S
SEAT, WITHOUT MEM-
ORY), INSPECTION, Power
Seat System.>

• Power seat switch
• Power seat harness
• Relevant motor

asieps_tobira.book 21 ページ２０１２年２月１０日　金曜日　午後３時２６分

«
...
761
762
763
764
765
...
»

Содержание B9 TRIBECA WX 2007






























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для B9 TRIBECA WX 2007

Бренд: Jabra Страницы: 2

Бренд: Jabra Страницы: 38

Бренд: TATA Motors Страницы: 161

Бренд: TAUBENREUTHER Страницы: 11

Бренд: Yakima Страницы: 15

Cherokee 16 1982

Бренд: Jeep Страницы: 1311

FleetMaster Air FW8 Series

Бренд: SAF-HOLLAND Страницы: 20

Бренд: Honda Страницы: 85

Бренд: Saab Страницы: 288

Бренд: Sunsky Страницы: 9

Бренд: Parkeon Страницы: 43

Бренд: Kuda Страницы: 2

Бренд: Magneti Marelli Страницы: 2

INDICA eV2 XETA CNG

Бренд: TATA Motors Страницы: 24

Бренд: PAC Страницы: 5

Бренд: Percon Страницы: 49

Бренд: Kia Страницы: 233

Бренд: Mercedes-Benz Страницы: 585

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды