manualshive.com logo in svg

Subaru B9 TRIBECA WX 2007, Руководство пользователя


Поделиться
Скачать
background image

AB(diag)-125

Diagnostic Chart with Trouble Code

AIRBAG SYSTEM (DIAGNOSTICS)

Step

Check

Yes

No

1

CHECK POOR CONTACT OF CONNEC-
TORS.

Check for poor contact of the connectors 
between the airbag control module and the 
driver’s airbag module.

Is there poor contact?

Replace the airbag 
main harness 
along with body 
harness.

Go to step 

2

.

2

CHECK DRIVER’S AIRBAG MODULE.

1) Turn the ignition switch to OFF, disconnect 
the battery ground cable, and wait more than 20 
seconds.
2) Remove the driver’s airbag module.
3) Connect the connector (AB38) to the con-
nector (1N) in the test harness N.
4) Connect the airbag resistor to the connector 
(2N) of test harness N.
5) Connect the connector (1Q) in the test har-
ness Q to connector (AB37).
6) Connect the airbag resistor to the connector 
(2Q) of test harness Q.
7) Connect the battery ground terminal and 
turn the ignition switch to ON.

Does the airbag warning light 
illuminate for 6 seconds and go 
off?

Replace the 
driver’s airbag 
module. <Ref. to 
AB-14, Driver’s Air-
bag Module.>

Go to step 

3

.

3

CHECK ROLL CONNECTOR.

1) Turn the ignition switch to OFF, disconnect 
the battery ground cable, and wait more than 20 
seconds.
2) Disconnect the test harness N from connec-
tor (AB38).
3) Disconnect the test harness Q from connec-
tor (AB37).
4) Remove the instrument panel lower cover 
and disconnect the connector (AB7) from 
(AB2).
5) Connect the connector (1P) in the test har-
ness P to connector (AB2).
6) Connect the airbag resistor to the connec-
tors (2P) and (3P) of test harness P.
7) Connect the battery ground terminal and 
turn the ignition switch to ON.

Does the airbag warning light 
illuminate for 6 seconds and go 
off?

Replace the roll 
connector. <Ref. to 
AB-22, Roll Con-
nector.>

Go to step 

4

.

4

CHECK AIRBAG MAIN HARNESS (DRIV-
ER’S AIRBAG HARNESS).

1) Turn the ignition switch to OFF, disconnect 
the battery ground cable, and wait more than 20 
seconds.
2) Disconnect the airbag resistor from the con-
nectors (2P) and (3P) of test harness P.
3) Remove the console side cover lower on the 
passenger’s side and disconnect the connec-
tors (AB10) and (AB9).
4) Disconnect the connector (AB6) from the 
airbag control module, and connect the connec-
tor (1U) in the test harness U.
5) Connect the battery ground terminal and 
turn the ignition switch to ON. (Engine OFF)
6) Measure the voltage between connector 
(2U) in the test harness U and chassis ground.

Connector & terminal

(2U) No. 4 (+) — Chassis ground (–):
(2U) No. 2 (+) — Chassis ground (–):
(2U) No. 8 (+) — Chassis ground (–):
(2U) No. 12 (+) — Chassis ground (–):

Is the voltage less than 1 V?

Go to step 

5

.

Replace the airbag 
main harness 
along with body 
harness.

asieps_tobira.book  125 ページ  ２０１２年２月１０日　金曜日　午後３時２６分

Содержание B9 TRIBECA WX 2007






























































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для B9 TRIBECA WX 2007

Camcar 2155 Fitting Instructions preview
2155
Бренд: Camcar Страницы: 2
ABL eMH1 WALLBOX Manual preview
eMH1 WALLBOX
Бренд: ABL Страницы: 176
ABL eMH1 WALLBOX Installation Manual preview
eMH1 WALLBOX
Бренд: ABL Страницы: 94
RaceChip XLR User Manual preview
XLR
Бренд: RaceChip Страницы: 20
iDataLink BLADE-AL(TB)-TL2 Install Manual preview
BLADE-AL(TB)-TL2
Бренд: iDataLink Страницы: 9
Magneti Marelli BCF184 Installation Instructions preview
BCF184
Бренд: Magneti Marelli Страницы: 2
EUFAB 16465 Operating Instructions Manual preview
16465
Бренд: EUFAB Страницы: 12
Atera 080 705 User Information preview
080 705
Бренд: Atera Страницы: 3
Black Horse RB001BK Installation Instructions preview
RB001BK
Бренд: Black Horse Страницы: 5
Subaru Legacy 2011 Quick Reference Manual preview
Legacy 2011
Бренд: Subaru Страницы: 19
Oldsmobile 1998 Aurora Owner'S Manual preview
1998 Aurora
Бренд: Oldsmobile Страницы: 380
newmotion Dynamic Power Management Home - Module Installation Instruction preview
Dynamic Power Management Home - Module
Бренд: newmotion Страницы: 20
Ford Focus 2008 Quick Reference Manual preview
Focus 2008
Бренд: Ford Страницы: 2
Oldsmobile 1994 88 Owner'S Manual preview
1994 88
Бренд: Oldsmobile Страницы: 276
Volkswagen PASSAT CC - Brochure preview
PASSAT CC -
Бренд: Volkswagen Страницы: 32
Kargo Master 80070 Instruction Manual preview
80070
Бренд: Kargo Master Страницы: 17
INNO TR163 Installation Instructions preview
TR163
Бренд: INNO Страницы: 3
Edelbrock 4789 Installation Instructions preview
4789
Бренд: Edelbrock Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды