Subaru B9 TRIBECA WX 2007, Руководство пользователя

Страница: 595 / 861

LAN(diag)-20
Subaru Select Monitor
LAN SYSTEM (DIAGNOSTICS)
CAUTION:
• It is possible to control the original func-
tions of vehicle when registrations of body
integrated unit and function setting are corre-
sponded to vehicle equipment.
• When body integrated unit is a new part or
“Factory” mode, key illumination blinks to
show equipment settings have not been com-
pleted.
• Be sure not to change Factory initial set-
ting except installation of new body integrat-
ed unit.
NOTE:
“Factory” mode:
• Body integrated unit has not been set yet. It
can be recognized by key illumination blinking
with ignition switch turned to ON.
• All body integrated units as spare parts are set
to “Factory” mode. When replacing a body inte-
grated unit, be sure to perform the registration
operation.
“Market” mode:
Each settings have been set. It can be recognized
by key illumination coming on in concocting with
room light and going off with ignition switch turned
to ON.
7) Perform the Factory initial setting. On the «ECM
customizing” display screen of Subaru Select Mon-
itor, select the {Factory initial setting}.
8) Change the mode from Factory to Market.
9) Register the immobilizer key.
10) Perform the registration according to the proce-
dures of the “IMMOBILIZER REGISTRATION OP-
ERATION MANUAL”.
11) When the key registration is completed, per-
form the function setting (Module customization).
<Ref. to LAN(diag)-21, FUNCTION SETTING
(ECM CUSTOMIZING), OPERATION, Subaru Se-
lect Monitor.>
7. CLEAR MEMORY MODE
1) On the «Main Menu», select the {2. Each Sys-
tem Check}.
2) On the «System Selection Menu» display
screen, select the {Integ. unit mode}.
3) Select the [OK] after the information of body in-
tegrated unit type is displayed.
4) On the «Integ. Unit mode failure diag» display
screen, select the {Clear Memory}.
5) When “Done” is shown on the display screen,
turn the ignition switch to OFF.
NOTE:
For details concerning operation procedure, refer
to the “SUBARU SELECT MONITOR OPERATION
MANUAL”.
8 . FREEZE FRAME DATA
NOTE:
• Data stored at the time of trouble occurrence is
shown on display.
• Freeze frame data will be memorized maximum
to 20.
• If freeze frame data is not stored in memory cor-
rectly (caused by low power supply of body inte-
grated unit), DTC will be displayed with “?” on the
head of it in the Subaru Select Monitor display. This
shows it may be an unreliable reading.
Data Initial setting Registration Remarks
A/C ECM setting OFF
ON
Illumination control does not operate if A/C ECM setting is
set to “OFF” in case of model with auto A/C.
OFF
If A/C ECM setting is set to “ON” in case of model without
auto A/C, illumination change to night illumination and it is
difficult to be recognized.
P/W ECM setting OFF
ON
Set to “OFF”.
OFF
Center display setting OFF
ON
If center display failure is set to “OFF”, diagnosis for MFD
and navigation display cannot be performed.
OFF
Wiper deicer setting OFF
ON ON signal does not output with operation of wiper deicer
switch if wiper deicer is set to “OFF” in models with a wiper
deicer.
OFF
Rear fog light setting OFF
ON
Set to “OFF”.
OFF
Factory initial setting
(Reset of body integrated unit)
Factory
Factory (Reset) If Factory initial setting is set to “Factory”, registrations of
items above is changed to “OFF”. After setting, be sure to
set to “Market”.
Market (Settlement)
Display Contents to be monitored
Clear memory?
Clear function of DTC and
freeze frame data
asieps_tobira.book 20 ページ ２０１２年２月１０日 金曜日 午後３時２６分