Stratasys Objet260 Connex Скачать руководство пользователя страница 168

Страница: 168 / 224

Objet260 User Guide

6 Operating and Maintaining the Objet260 3D Printer

DOC-37004 Rev. E

6-35

6. Remove the two screws securing the covering of the roller waste collector

and remove it.

Be very careful to save the covering screws. These are special screws; if
they are lost, you need to order replacements.

Figure 6-39 Removing the roller waste collector covering

7. Remove the covering by pulling it out, and then lower it.

8. Clean the roller waste collector and the scraper blade surface using cotton

swabs. Make sure to remove any remaining printing materials.

Figure 6-40 Cleaning the roller waste collector

Before replacing the covering, you can check the effectiveness of the roller
scraper

—

see below.

To check the effectiveness of the roller scraper:

1. Put on the cleaning gloves.

2. Wet a cloth with isopropanol.

3. Use the cloth to wet the bottom of the roller.

4. Turn the roller slowly with your hand. As the blade scrapes the roller,

make sure the isopropanol is spread evenly over the entire length of the
blade.

5. Inspect the roller. If it is not dry, replace the blade. (See "Replacing the

Roller Scraper" on the next page.)

Содержание Objet260 Connex

































































































































































































































Результаты поиска

Содержание Objet260 Connex

Отзывы:

Бренды по названию

Популярные бренды

Stratasys Objet260 Connex, Руководство пользователя

Результаты поиска

Содержание Objet260 Connex

Отзывы:

Бренды по названию

Популярные бренды