STE POTENZA 160, Руководство по эксплуатации

Страница: 22 / 40

• Wear a face shield to protect eyes and face.
• Shape tungsten electrode only on grinder withproper guards in a
safe location wearing properface, hand, and body protection.
• Sparks can cause fires — keep flammables away.
4
• Do not press gun trigger until instructed to doso.
• Do not point gun toward any part of the body,other people, or any
metal when threading welding wire.
4
MOVING PARTS can cause injury.
• Keep away from moving parts such as fans.
• Keep all doors, panels, covers, and guardsclosed and securely
in place.
• Have only qualified persons remove doors, panels, covers,
or guards for maintenance as necessary.
• Reinstall doors, panels, covers, or guards when maintenance is
finished and before reconnecting input power.
4
H.F. RADIATION can cause interference.
• High-frequency (H.F.) can interfere with radionavigation, safety
services, computers, andcommunications equipment.
• Have only qualified persons familiar withelectronic equipment
perform this installation.
• The user is responsible for having a qualified electrician prompt-
ly correct any interference problem resulting from the installa-
tion.
• Have the installation regularly checked and maintained.
• Keep high-frequency source doors and panels tightly shut,
keep spark gaps at correct setting, and use grounding and
shielding tominimize the possibility of interference.
4
ARC WELDING can cause interference.
• Electromagnetic energy can interfere withsensitive electronic
equipment such ascomputers and computer-driven
equipment such as robots.
• Be sure all equipment in the welding area iselectromagnetically
compatible.
• To reduce possible interference, keep weld cables as short
as possible, close together, and down low, such as on the floor.
• Locate welding operation 100 meters from any sensitive elec-
tronic equipment.
• Be sure this welding machine is installed and grounded
according to this manual.
• If interference still occurs, the user must take extra measures
such as moving the welding machine, using shielded
cables,using line filters, or shielding the work area.
2.3.-EMF Information
To reduce magnetic fields in the workplace, use the
followingprocedures:
1. Keep cables close together by twisting or taping them, or using
acable cover.
WELDING WIRE can cause injury.
ENGLISH
18
18
4
Noise from some processes or equipment candamage hearing.
• Wear approved ear protection if noise level is high.
4
CYLINDERS can explode if damaged.
Shielding gas cylinders contain gas under highpressure. If
damaged, a cylinder can explode. Sincegas cylinders are
normally part of the weldingprocess, be sure to treat them
carefully.
• Protect compressed gas cylinders from excessive heat,
mechanical shocks, physical damage, slag, open flames,
sparks, and arcs.
• Install cylinders in an upright position by securing to a
stationarysupport or cylinder rack to prevent falling or tipping.
• Keep cylinders away from any welding or other electrical circuits.
• Never drape a welding torch over a gas cylinder.
• Never allow a welding electrode to touch any cylinder.
• Never weld on a pressurized cylinder − explosion will result.
• Use only correct shielding gas cylinders, regulators, hoses, and
fittings designed for the specific application; maintain them
and associated parts in good condition.
• Turn face away from valve outlet when opening cylinder valve.
• Keep protective cap in place over valve except when cylinder is
inuse or connected for use.
• Use the right equipment, correct procedures, and sufficient num-
ber of persons to lift and move cylinders.
• Read and follow instructions on compressed gas
cylinders,associated equipment, and Compressed Gas
Association (CGA)publication P-1 listed in Safety Standards.
4
FIRE OR EXPLOSION hazard.
• Do not install or place unit on, over, or nearcombustible surfaces.
• Do not install unit near flammables.
• Do not overload building wiring − be sure power supply system is
properly sized, rated, and protected to handle this unit
4
FALLING UNIT can cause injury.
• Use lifting eye to lift unit only, NOT runninggear, gas cylinders, or
any other accessories.
• Use equipment of adequate capacity to lift andsupport unit.
• If using lift forks to move unit, be sure forks arelong enough to
extend beyond opposite side ofunit.
4 OVERUSE can cause OVERHEATING
• Allow cooling period; follow rated duty cycle.
• Reduce current or reduce duty cycle beforestarting to weld
again.
• Do not block or filter airflow to unit.
4
FLYING SPARKS can cause injury.
NOISE can damage hearing.