Siemens SITRANS F M Intermag 2 Скачать руководство пользователя страница 30

Страница: 30 / 130

Installation

3-8

SITRANS FM Intermag 2 Flow Transmitter

Operating Manual - A5E00102775-03

3.4

Electrical Connection

3.4.1

General Information

Warning

The pertinent regulations must be observed for electrical installation.

Never install the device with the mains voltage switched on !
Danger of electric shock!

The electrodes and magnetic current line may only be connected when
the device is not connected to the power supply.

Please note that the version for the UC 24 to 30 V power supply may
only be connected to SELV or PELV circuits.

Housing covers may only be unscrewed by

qualified personnel

when

the housing is under voltage (power supply).

Handling devices with explosion protection you must pay
particular attention to all information in section 3.6.

The SITRANS FM magnetic-inductive measuring devices comply with
the following protection classes:

Version for 100 to 230 V AC:

Protection class

Version for UC 24 to 30 V:

Protection class

III

It generally applies for electrical installation:

Only use heat-resistant cables if high temperatures occur on the
housing, e.g. due to heat conductance from the sensor/measuring
pipe. Lay the cables so that they do not touch the hot sensor tube.

Lid of terminal box

Cable gland

Figure 3-9

Example of laying cables before connecting the lines

Содержание SITRANS F M Intermag 2



































































































































Результаты поиска

Содержание SITRANS F M Intermag 2

Отзывы:

Похожие инструкции для SITRANS F M Intermag 2

Бренды по названию

Популярные бренды

Siemens SITRANS F M Intermag 2, Руководство по эксплуатации

Результаты поиска

Содержание SITRANS F M Intermag 2

Отзывы:

Похожие инструкции для SITRANS F M Intermag 2

Бренды по названию

Популярные бренды