Siemens SITRANS F M Intermag 2 Скачать руководство пользователя страница 32

Страница: 32 / 130

Installation

3-10

SITRANS FM Intermag 2 Flow Transmitter

Operating Manual - A5E00102775-03

Signal line

Terminal box

Electrode line

Power supply

for power supply
and signal lines

Magnetic current line

Terminal box
for magnetic current

and electrode line

Potential equalization

Figure 3-10 SITRANS FM Intermag 2, electrical connections

3.4.2

Connection of the Power Supply

Only connect the device to the supply which matches the
specifications on the rating plate.

Connect the power supply by an easily accessible and appropriate
labeled isolating device and fuse (max. 4 A) or an easily accessible
circuit breaker (max. 4 A).

Use cables with a cross section of at least 1.5 mm

and double or

reinforced insulation for the power supply.

Connect the PE conductor of the power supply to the ground
terminal

in the terminal box. The line length must be

dimensioned so that the PE conductor comes away last when the
cable is pulled.

3.4.3

Connection of the signal cables

Lay the signal cables separately from cables with voltages

60 V.

Only use signal cables with twisted wire pairs.

Avoid laying signal cables close to large electrical installations or
use - if possible - only shielded cables.

The full HART 5.1 specification only applies when using shielded
cables.

Содержание SITRANS F M Intermag 2



































































































































Результаты поиска

Содержание SITRANS F M Intermag 2

Отзывы:

Похожие инструкции для SITRANS F M Intermag 2

Бренды по названию

Популярные бренды

Siemens SITRANS F M Intermag 2, Руководство по эксплуатации

Результаты поиска

Содержание SITRANS F M Intermag 2

Отзывы:

Похожие инструкции для SITRANS F M Intermag 2

Бренды по названию

Популярные бренды