Siemens SITRANS F M Intermag 2 Скачать руководство пользователя страница 105

Страница: 105 / 130

Maintenance

6-5

SITRANS FM Intermag 2 Flow Transmitter
Operating Manual - A5E00102775-03

Error

Diagnosis

Remedy

Measuring deviations,

Inlet and outlet lines insufficient

Change installation (see section 3.2.2)

measuring errors

Highly turbulent flow profile

Change inlet line, use flow rectifier, reduce
diameter of tube

For mass measurement: medium
density set incorrectly

Correct density according to current medium
(menu

3.1.4

)

Hydraulic calibration values faulty

Check hydraulic calibration values CFH and
ZPH. According to the sensor rating plate and
correct if necessary
(menus

6.7.2

and

6.7.3

Electric calibration faulty

Run self-test (menu

2.4.1

);

Check device status (menu

2.1

of ”Calibration failure measuring module”
is displayed, send in the complete electronics
for repair

Application-dependent
calibration values faulty

Reset zero point correction (menu

6.6.1

) to 0

and/or reset calibration factor (menu

6.7.1

)

to 1.0.
Alternatively: Make zero correction
(menu

6.6.2

) and manual adaptation of the

calibration factor (menu

6.7.1

)

Measured value too low at

Set attenuation too high

Reduce filter time constant (menu

3.1.7.1

)

dosing

Fault blanking activated

Deactivate noise suppression (menu

3.1.7.3

)

Magnetic field frequency too low

Device may not be suitable for this application

Measured value too low in
pulsed flow

Temporary exceeding of internal
working range

Increase URV (menu

3.1.2

)

Unfavorable hydraulic conditions

Install sensor on the suction side of the
corresponding pump or in front of the feeding
valve

Output current does not
correspond to the current
flow and remains at a

There is a fault, failure signal 3.6,
22 or 24 mA is output (depending
on the setting under menu

4.1.2

)

Determine source of fault under device status
(menu 2.1) (see section

5.3.2

)

flow and remains at a
constant value

Load too high

Reduce total load including the cable
resistance to < 600

Ω

Current output or power supply
defective

Replace complete electronics

Communication via HART
not possible

Minimum load of 230

Ω

not

available

Increase load to at least 230

Ω

and connect

HART Modem/Communicator parallel to this

not possible

available

HART Modem/Communicator parallel to this
load

Содержание SITRANS F M Intermag 2



































































































































Результаты поиска

Содержание SITRANS F M Intermag 2

Отзывы:

Похожие инструкции для SITRANS F M Intermag 2

Бренды по названию

Популярные бренды

Siemens SITRANS F M Intermag 2, Руководство по эксплуатации

Результаты поиска

Содержание SITRANS F M Intermag 2

Отзывы:

Похожие инструкции для SITRANS F M Intermag 2

Бренды по названию

Популярные бренды