manualshive.com logo in svg

Siemens SIREMOBIL Iso-C 3D, Руководство по установке, Страница: 4 / 98

Поделиться
Скачать
Siemens SIREMOBIL Iso-C 3D Скачать руководство пользователя страница 4

0 - 4

Contents

SIREMOBIL Iso-C 3D

 

SPR2-230.814.01

Page  4 of  6

Siemens AG

 

Rev. 05

08.04

CS PS 24

Medical Solutions

 

Cable no. 2, item number n.a.   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4 - 6
Cable no. 1, item number n.a.   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4 - 6
Cable no. 6, item number n.a.   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4 - 6
Orbital drive cable set, item no. 71 39 970  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4 - 7
Cable no. 7, item number n.a. (Fig. 18).  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4 - 8

Additional work with the LITHOSTAR MODULARIS option   .  .  .  .  .  .  .  .  .  .  .  .  .  .4 - 11

Checking the existing configuration.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .4 - 11

Installing the new LITHOSTAR MODULARIS interface   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .4 - 12

5 ______ 2. Part of activities independent of serial number ____________________5 - 1

Orbital drive.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  5 - 1

Coupling unit  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  5 - 2

Drive belt  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  5 - 4

Angulation measurement .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  5 - 5
Wiring for the orbital drive   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  5 - 6

6 ______ 3. Part of activities independent of serial number ____________________6 - 1

Preparations on the monitor trolley .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  6 - 1
Replacing the monitor   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  6 - 2

SIMOMED HM  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  6 - 2
Cable no. 13, item number n.a. .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  6 - 4
TFT Displays  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  6 - 6

PC support  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 14

Holes for PC support  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 14

Keyboard tray .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 16
Rear panel of the monitor trolley  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 22
Installing the PC  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 22

Video switcher   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 23
Cut-off delay D210, item no. 71 40 071.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 25
Cabling of the mouse and keyboard  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 27
Monitor cable, no. n.a., item number 30 65 844   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 27
Video cable, no. n.a., item number n.a..  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 27
Monitor cable, no. n.a., item number 30 65 844   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 28
Cable, no. 10, item number n.a.   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 29
Video Out cable, no. n.a., item number n.a.   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 29
Cable no. 14, item number n. a.   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 30
SCSI cable, no. .n.a., item number 30 66 180  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 31
Cable no. 11, item number n.a.,   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 32
Printer is available   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 32
No printer available .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 32
Cable no. 15, item number n.a.,   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 33
Cable no. 16, item number n.a. .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 34
Cables no. 8 and 9, item number n.a.   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 36
Attaching the video switcher  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 37
System manual drawer .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 37
Zipper hose .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 38
Cable no. 12, item number n.a. .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .6 - 39

Page

Содержание SIREMOBIL Iso-C 3D



































































































Отзывы:

Нет отзывов