manualshive.com logo in svg

Siemens SIREMOBIL Iso-C 3D, Руководство по установке, Страница: 77 / 98

Поделиться
Скачать
Siemens SIREMOBIL Iso-C 3D Скачать руководство пользователя страница 77

3. Part of activities independent of serial number

6 - 27

Siemens AG

 

SPR2-230.814.01

Page 27 of 42

SIREMOBIL Iso-C 3D

Medical Solutions

Rev. 05

08.04

CS PS 24

 

 

Cabling of the mouse and keyboard 

6

•

Route the cables for the mouse and keyboard through the opening downward at the left 
side. 

•

Connect the keyboard cable at the PC keyboard port. 

•

Connect the mouse cable to the "Primary Pointing Device" (Fig. 68) plug-in location on 
the mouse port adapter.

•

Connect the cable of the computer mouse port to the mouse port at the PC. 

Monitor cable, no. n.a., item number 30 65 844

6

•

Connect the cables to video switcher 1 (see Fig. 69), output terminal "out",
green to G, blue to H/C, red to V.

Video cable, no. n.a., item number n.a.

6

•

Connect the video cable (has already be routed downward) from the monitor to input G at 
video switcher 1 (see Fig. 69).

Fig. 69 Mouse port adapter

Fig. 70 Video switcher 1 and 2

Video switcher 1

Video switcher 2

Markierung für Tastaturschublade

Содержание SIREMOBIL Iso-C 3D



































































































Отзывы:

Нет отзывов