manualshive.com logo in svg

Siemens SIREMOBIL Iso-C 3D, Руководство по установке, Страница: 91 / 98

Поделиться
Скачать
Siemens SIREMOBIL Iso-C 3D Скачать руководство пользователя страница 91

3. Part of activities independent of serial number

6 - 41

Siemens AG

 

SPR2-230.814.01

Page 41 of 42

SIREMOBIL Iso-C 3D

Medical Solutions

Rev. 05

08.04

CS PS 24

 

 

Covers

6

Attaching the PC covers 

6

•

Connect the protective conductor (1000 mm long) from the front cover of the base plate 
to the PC support (Fig. 95). 

•

Attach the front cover (Fig. 94). 

•

Connect the protective conductor (150 mm long) from the side cover of the base plate to 
the PC support. 

•

Connect the protective conductor (550 mm long) from the rear panel of the PC to the 
base plate of the PC support. 

•

Route the protective conductor from the base plate of the PC support to the protective 
conductor bar in the monitor trolley and connect it. 

•

Attach the rear panel of the monitor trolley. 

•

Affix the 3D label to the monitor (Fig. 96).

Fig. 95 PC with covers

Fig. 96 Grounding of PC housing

Fig. 97 3D label

3D label 

Содержание SIREMOBIL Iso-C 3D



































































































Отзывы:

Нет отзывов