Siemens SIREMOBIL Iso-C 3D Скачать руководство пользователя страница 44

Страница: 44 / 98

SIREMOBIL Iso-C 3D

SPR2-230.814.01

Page 2 of 8

Siemens AG

Rev. 05

08.04

CS PS 24

Medical Solutions

5 - 2

2. Part of activities independent of serial number

Coupling unit

•

Fit the coupling unit onto the centering disk, the shaft has to engage the connecting piece
(Fig. 4).

•

Press the coupling unit against the centering disk and attach it to the left and right using
the two threaded pins (Fig. 5).

•

Loosen the belt tightener at the coupling unit (Fig. 6).

•

Push the wide toothed belt onto the motor (Fig. 6).

•

Tighten the belt. On the opposite side of the belt tightener, it should be possible to press
down the belt approx. 2 - 3 mm with your thumb (Fig. 7).

Fig. 4

Centering disk

Fig. 5

Coupling unit

Fig. 6

Toothed belt

Fig. 7

Belt tensioning

threaded pin

connecting piece

2 to 3 mm

tightener

toothed belt

Содержание SIREMOBIL Iso-C 3D



































































































Результаты поиска

Содержание SIREMOBIL Iso-C 3D

Отзывы:

Siemens SIREMOBIL Iso-C 3D, Руководство по установке, Страница: 44 / 98

Результаты поиска

Содержание SIREMOBIL Iso-C 3D

Отзывы: