manualshive.com logo in svg

Siemens SIREMOBIL Iso-C 3D, Руководство по установке, Страница: 40 / 98

Поделиться
Скачать
Siemens SIREMOBIL Iso-C 3D Скачать руководство пользователя страница 40

SIREMOBIL Iso-C 3D

 

SPR2-230.814.01

Page 12 of 14

Siemens AG

 

Rev. 05

08.04

CS PS 24

Medical Solutions

4 - 12

Kapitelüberschrift hier eintragen

 

Installing the new LITHOSTAR MODULARIS interface

4

•

For easier accessibility, the SIREMOBIL Iso-C lifting column can be moved to the top 
position. After this, disconnect the SIREMOBIL Iso-C from the power supply.

•

Remove the rear panel of the SIREMOBIL Iso-C basic unit.

•

Screw down the drilling template as shown in Fig. 25.

•

To prevent drill shavings from melting into the surface, place a cloth or thin cardboard 
over the cover (Fig. 25).

Inside:

•

With the 3.5 mm drill supplied, drill 3 holes using the holes of the template as a reference.

•

Remove the drilling template.

•

Using the step drill supplied, open the center hole to 28 mm.

•

To do this, drill open the hole until the step drill is immersed in the plate down to the mark 
shown in Fig. 26 (approx. 0.5 mm from the largest drilled diameter of 30 mm).

•

Drill slowly! (approx. 300 to 500 rpm).

Fig. 25

Fig. 26

Содержание SIREMOBIL Iso-C 3D



































































































Отзывы:

Нет отзывов