manualshive.com logo in svg

Siemens SIREMOBIL Iso-C 3D, Руководство по установке, Страница: 55 / 98

Поделиться
Скачать
Siemens SIREMOBIL Iso-C 3D Скачать руководство пользователя страница 55

3. Part of activities independent of serial number

6 - 5

Siemens AG

 

SPR2-230.814.01

Page 5 of 42

SIREMOBIL Iso-C 3D

Medical Solutions

Rev. 05

08.04

CS PS 24

 

 

•

Remove the packaging from the monitor and place the monitor on the carton (Fig. 12). 

•

Remove the rear cover (Fig. 13).

•

Remove the monitor dome of Simomed HM (2 screws at the back). 

•

Attach the monitor carrier to the monitor using 6 screws (Fig. 14). 

•

Place the monitor on the adapter and tighten the two neck screws (Fig. 15).

•

Attach the two cables at the cable supports at the monitor (Fig. 15).

•

Slide the monitor housing over it. 

•

Connect the cables at the monitor, 
green to video, blue to H/H+V, red to V.

•

Connect the power plug of the old monitor to the new monitor. 

Fig. 12 Monitor, unpacked

Fig. 13 Monitor cover removed

Fig. 14 Monitor support

Fig. 15 Attaching the cables

Содержание SIREMOBIL Iso-C 3D



































































































Отзывы:

Нет отзывов