manualshive.com logo in svg

Siemens SIREMOBIL Iso-C 3D, Руководство по установке, Страница: 82 / 98

Поделиться
Скачать
Siemens SIREMOBIL Iso-C 3D Скачать руководство пользователя страница 82

SIREMOBIL Iso-C 3D

 

SPR2-230.814.01

Page 32 of 42

Siemens AG

 

Rev. 05

08.04

CS PS 24

Medical Solutions

6 - 32

3. Part of activities independent of serial number

 

Cable no. 11, item number n.a., 

6

is included in system cabling 71 39 855

 

•

Connect plug 3D-PC I/O card (see Fig. 76) to the "Relay card" connector at the PC and 
secure it with screws. 

•

Route the end VU1 to video switcher 1 (see Fig. 69), from the left side toward the top.

•

Attach cable ends 1-3 to the Remote connector (Fig. 77),
1 to 1, 2 to 2, 3 to 3.

•

Route the end VU2 to video switcher 2 (see Fig. 69), from the right side toward the top. 

•

Attach cable ends 1-3 to the Remote connector (Fig. 77),
1 to 1, 2 to 2, 3 to 3.

•

Connect the plug to "Remote Status" on video switcher 2 (see Fig. 69). 

•

Connect the "PC out" plug to D210 X3.

Printer is available

6

•

If a printer exists, disconnect the Remote plug at the printer and connect it with the 
coupling of the Memoskop. Route the cable upward to the left. 

•

Connect the ’Printer Remote’ plug to the ’Remote’ printer connection. 

No printer available

6

•

If there is no printer, connect the ’Printer Remote’ plug with the Memoskop coupling. If 
required, insulate the metal housing with tape. 

•

Plug D100.X1001 is not connected. Insulate the contacts, roll up the cable and attach it 
using cable ties. 

Fig. 77 Cable no. 11

Fig. 78 Video switcher, remote connector 

1

2

3

connector 3D PC I/O

Содержание SIREMOBIL Iso-C 3D



































































































Отзывы:

Нет отзывов