Siemens SIREMOBIL Iso-C 3D Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 98

Siemens SIREMOBIL Iso-C 3D Скачать руководство пользователя страница 14

SIREMOBIL Iso-C 3D

SPR2-230.814.01

Page 2 of 14

Siemens AG

Rev. 05

08.04

CS PS 24

Medical Solutions

2 - 2

Actions up to serial number 1408

Cover of the cable module

2

•

Remove the cover. It will later be replaced by a new one. Dispose of all the covers that
are no longer needed.

Drilling and threading holes at the cable module

2

•

Attach the drilling template for the orbital drive and angulation measurements at the
cable module (Fig. 2). Ensure that the template is attached to the right as seen from the
system.
(Depending on the time of delivery, the cable module comes with different sides that may
or may not include recesses. Already existing recesses have nothing to do with the 3D
option. The steps for drilling are the same for both versions).

•

Attach the special drill over the openings of the drilling template. Drill the holes with the
55 mm crown bit (Fig. 3).

•

The drill has to be positioned upside down while you drill the holes. Secure the drill with
the belt included in the drill kit.

•

Ensure that drill shavings do not drop into the cable module.

Fig. 2

Drilling template, orbital drive

Fig. 3

Drill

«
...
12
13
14
15
16
...
»

Содержание SIREMOBIL Iso-C 3D



































































































Отзывы:

Нет отзывов