Siemens SIREMOBIL Iso-C 3D Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 98

Siemens SIREMOBIL Iso-C 3D Скачать руководство пользователя страница 59

3. Part of activities independent of serial number

6 - 9

Siemens AG

SPR2-230.814.01

Page 9 of 42

SIREMOBIL Iso-C 3D

Medical Solutions

Rev. 05

08.04

CS PS 24

Installation of the support arm on the monitor trolley

•

Open the rear cover of the support arm base on the TFT display.

•

Route the free cable ends of the new power line cables (included in the attachment of the
TFT Display) downwards through the support arm holder (2/Fig. 24), through the center
cable bush of the monitor trolley and through the lateral rail to the ON/OFF assembly
(Fig. 23) and connect them to the terminal blocks:

- Connect the brown cable ends to terminal block X2.1
- Connect the blue cable ends to terminla block X2.2
- Connect the protective ground cable ends (ye/gn) to the protective conductor bars

(1/Fig.23).

•

Route the cable ends of the video cables upwards through the support arm base
(1/Fig.24) and further through the support arm holder (2/Fig. 24).

•

Place the support arm base above the center cable bush (Fig.24).

•

Starting with the logbook compartment, tighten the screws of the support arm base on
the monitor trolley. Use 4 Allen screws M6 x 20, 4 lock washers and 4 plate washers for
this (Fig. 24).

Fig. 24 Installation of the support arm

The new poer line cables have a length of approx. 2.6m and are
equiped with a straight femal connector on one cable end.

Mark for the keyboard tray

NOTE

«
...
57
58
59
60
61
...
»

Содержание SIREMOBIL Iso-C 3D



































































































Отзывы:

Нет отзывов