Siemens SIREMOBIL Iso-C 3D Скачать руководство пользователя страница 64

Страница: 64 / 98

SIREMOBIL Iso-C 3D

SPR2-230.814.01

Page 14 of 42

Siemens AG

Rev. 05

08.04

CS PS 24

Medical Solutions

6 - 14

3. Part of activities independent of serial number

PC support

Holes for PC support

•

Place the aluminium spacers (2) on the two rollers (Fig. 31).

•

Disassemble the PC housing. You will still need the white foam rubber material.

•

Position the PC housing on the spacer. The housing should be flush at the front. If so,
attach it with a screw clamp. The ground connection should point down toward the back
of the monitor trolley (Fig. 32).

•

Mark the holes (Fig. 32).

•

Remove the PC housing and spacers again.

•

Punch-mark the holes.

•

Start to drill the 4 holes at the marked locations using a 3.2 mm drill bit. Ensure that you
are not drilling into cables at the monitor trolley.

•

Complete drilling the 4 holes by using a 6 mm drill bit.

•

Deburr the holes.

•

Remove the shavings. Use a vacuum cleaner, if needed.

Fig. 32 Spacers

Fig. 33 PC housing

Содержание SIREMOBIL Iso-C 3D



































































































Результаты поиска

Содержание SIREMOBIL Iso-C 3D

Отзывы:

Siemens SIREMOBIL Iso-C 3D, Руководство по установке, Страница: 64 / 98

Результаты поиска

Содержание SIREMOBIL Iso-C 3D

Отзывы: