manualshive.com logo in svg

Siemens SIREMOBIL Iso-C 3D, Руководство по установке, Страница: 79 / 98

Поделиться
Скачать
Siemens SIREMOBIL Iso-C 3D Скачать руководство пользователя страница 79

3. Part of activities independent of serial number

6 - 29

Siemens AG

 

SPR2-230.814.01

Page 29 of 42

SIREMOBIL Iso-C 3D

Medical Solutions

Rev. 05

08.04

CS PS 24

 

 

Cable, no. 10, item number n.a.

6

•

Remove the keyboard connector at the Memoskop (Fig. 72). 

•

Connect the "Memoskop RS 2322 " plug of cable no. 10 (Fig. 71) to the keyboard 
connection at the Memoskop and secure it. 

•

Connect the keyboard connection plug to the disconnected keyboard connection and 
secure it. 

•

Pull plug "3D PC RS 232" through the opening down to the left and connect to it to the PC 
serial port RS232. 

Video Out cable, no. n.a., item number n.a.

6

•

Insert the VGA plug (Fig. 58) into the left graphics card. 

•

Connect the Video Out plug with BNC coupling/ Cinch (see Fig. 73). 

Fig. 72 Cable no. 10

Fig. 73 Memoskop connector 

Fig. 74  Video Out cable including terminator and BNC coupling 

Markierung für Tastaturschublade

terminator

BNC coupling

VGA plug

Содержание SIREMOBIL Iso-C 3D



































































































Отзывы:

Нет отзывов