Siemens SIREMOBIL Iso-C 3D Скачать руководство пользователя страница 56

Страница: 56 / 98

SIREMOBIL Iso-C 3D

SPR2-230.814.01

Page 6 of 42

Siemens AG

Rev. 05

08.04

CS PS 24

Medical Solutions

6 - 6

3. Part of activities independent of serial number

TFT Displays

Dismantling existing monitors

•

Both monitors should be removed as follows.

•

Remove the monitor covers (Fig. 16).

•

Remove the shielding plates (Fig. 17).

•

Remove the connection housing (only for SIMOMED N monitor 11 02 628, Fig. 18).

•

Unplug all cables from the monitor to be replaced.

•

Remove the two screws on each monitor attachment (Fig. 19).

•

Lift both monitors down.

•

Reattach all the parts removed from the monitor.

If a SIMOMED HM monitor was ordered and delivered, disregard
this section. Continue with the section "PC support".

Fig. 16 Monitor cover

Fig. 17 Shielding plate

Fig. 18 Connection housing

Fig. 19 Monitor attachment

NOTICE

Markierung für Tastaturschublade

Содержание SIREMOBIL Iso-C 3D



































































































Результаты поиска

Содержание SIREMOBIL Iso-C 3D

Отзывы:

Siemens SIREMOBIL Iso-C 3D, Руководство по установке, Страница: 56 / 98

Результаты поиска

Содержание SIREMOBIL Iso-C 3D

Отзывы: