manualshive.com logo in svg

Siemens 1PH818, Инструкция по эксплуатации и установке

"Siemens 1PH818" - мощный электродвигатель, предназначенный для применения в различных индустриальных секторах. Вы можете скачать бесплатно Руководство по эксплуатации и инструкции по установке на manualshive.com. Получите подробную информацию о данном изделии и его функциях, чтобы использовать его эффективно и безопасно.

Поделиться
Скачать
background image

7.2

Insulation resistance and polarization index

Measuring the insulation resistance and polarization index (PI) provides information on the 

condition of the machine. It is therefore important to check the insulation resistance and the 

polarization index at the following times:     
● Before starting up a machine for the first time
● After an extended period in storage or downtime
● Within the scope of maintenance work
The following information is provided regarding the state of the winding insulation:
● Is the winding head insulation conductively contaminated?
● Has the winding insulation absorbed moisture?
As such, you can determine whether the machine needs commissioning or any necessary 

measures such as cleaning and/or drying the winding:
● Can the machine be put into operation?
● Must the windings be cleaned or dried?
Detailed information on testing and the limit values can be found here:
"Testing the insulation resistance and polarization index"  (Page 50) 

NOTICE
Damage to the converter
The electronics of the integrated converter can be destroyed when measuring the insulation 

resistance at the EC external fan with a voltage exceeding 305 V.
● Do not measure the insulation resistance of the EC external fan.
● More information can be found in the instructions of the EC external fan.

7.3

Checks to be carried out prior to commissioning 

Once the system has been correctly installed, you should check the following prior to 

commissioning:

Note
Checks to be carried out prior to commissioning 
The following list of checks to be performed prior to commissioning does not claim to be 

complete. It may be necessary to perform further checks and tests in accordance with the 

specific situation on-site. 

● The machine is undamaged.
● The machine has been correctly installed and aligned, the transmission elements are 

correctly balanced and adjusted.

Commissioning

7.3 Checks to be carried out prior to commissioning 

SIMOTICS M-1PH8  1PH818., 1PH822.

Operating Instructions 07/2016

85

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1PH818

Nanni N2.10 Operator'S Manual preview
N2.10
Бренд: Nanni Страницы: 67
STG-BEIKIRCH EM Tandem RWA Technical Information And Operating Instruction preview
EM Tandem RWA
Бренд: STG-BEIKIRCH Страницы: 9
MerCruiser Vazer 100 Owner'S Manual preview
Vazer 100
Бренд: MerCruiser Страницы: 118
MerCruiser Sterndrive 4.3L TKS Owner'S Manual preview
Sterndrive 4.3L TKS
Бренд: MerCruiser Страницы: 130
MerCruiser QSD 2.0 Manual preview
QSD 2.0
Бренд: MerCruiser Страницы: 135
Volvo D16F Service Bulletin preview
D16F
Бренд: Volvo Страницы: 11
Volvo D13 Installation Manual preview
D13
Бренд: Volvo Страницы: 36
Volvo D1-13 B Workshop Manual preview
D1-13 B
Бренд: Volvo Страницы: 48
KAZZ 2.2ci Instruction Manual preview
2.2ci
Бренд: KAZZ Страницы: 11
Yanmar 2GM20 Operation Manual preview
2GM20
Бренд: Yanmar Страницы: 63
Barrus Shire 30 RB Manual preview
Shire 30 RB
Бренд: Barrus Страницы: 51
Mitsubishi Heavy Industries S4S Service Manual preview
S4S
Бренд: Mitsubishi Heavy Industries Страницы: 220
Briggs & Stratton 146400 Operating And Maintenance Instruction Manual preview
146400
Бренд: Briggs & Stratton Страницы: 6
Iveco C78 ENT M50 Installation Instruction preview
C78 ENT M50
Бренд: Iveco Страницы: 40
Silicon Laboratories SENSORLESS-BLDC-MOTOR-RD User Manual preview
SENSORLESS-BLDC-MOTOR-RD
Бренд: Silicon Laboratories Страницы: 12
EMAK K1600 AVD Operating Manual preview
K1600 AVD
Бренд: EMAK Страницы: 152
Piusi V100 Instructions For Installation, Use And Maintenance Manual preview
V100
Бренд: Piusi Страницы: 64
rojaflex 90100017 Original Assembly And Operating Instructions preview
90100017
Бренд: rojaflex Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды