Siemens 1PH818 Скачать руководство пользователя страница 91

Страница: 91 / 198

Operation

When carrying out any work on the machine, observe the general safety instructions

(Page 13) and the specifications contained in EN 50110‑1 regarding safe operation of electrical

equipment.

8.1

Safety guidelines in operation

WARNING

Live parts
Terminal boxes accommodate live parts and components. If you open the terminal box cover,

this can result in death, serious injury or material damage.
● When the machine is in operation, the terminal boxes must remain closed at all times.

Terminal boxes may be opened only when the machine is stopped and de-energized.

WARNING

Rotating and live parts
Rotating or live parts are dangerous. If you remove the required covers, this can result in

death, serious injury or material damage.
● Any covers that prevent live electrical or rotating parts from being touched, ensure

compliance with a particular degree of protection or are required for ensuring proper air

flows, and hence effective cooling, must not be opened during operation.

WARNING

Fire hazard resulting from hot surfaces
Certain parts of the machine become hot during operation. Severe burns can result from

contact with these parts.
● Check the temperature of parts before touching them. If required, apply suitable protective

measures.

● Allow the machine to cool before starting work on the machine.

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

Содержание 1PH818







































































































































































































Результаты поиска

Содержание 1PH818

Отзывы:

Бренды по названию

Популярные бренды

Siemens 1PH818, Инструкция по эксплуатации и установке

Результаты поиска

Содержание 1PH818

Отзывы:

Бренды по названию

Популярные бренды