Siemens 1PH818 Скачать руководство пользователя страница 171 | Manualshive

Страница: 171 / 198

background image

Danger of being sucked in!

Do not wear loose or hanging clothing, jewellery, etc., tie together long hair and cover it.

Attention, hot surface!

•

Temperatures of above 85

°

C can occur on the motor surfaces, especially on the controller

housing!

2.7

Modi

ﬁ

cations / interventions in the device

Attention!

For reasons of safety, no unauthorized interventions or modi

ﬁ

cations may be made on the device. All

planned modi

ﬁ

cations must be authorized by the manufacturer in writing.

Use only genuine spare parts / genuine wearing parts / genuine accessories from ZIEHL-ABEGG.Th-
ese parts were speci

ﬁ

cally designed for the device. There is no guarantee that parts from non-original

sources are designed and manufactured in correspondence with load and safety requirements.
Parts and optional equipment not supplied by ZIEHL-ABEGG are not approved by ZIEHL-ABEGG for
use.

2.8

Operator

’

s obligation of diligence

•

The contractor or owner must also ensure that the electric systems and equipment are operated
and maintained in accordance with electro-technical regulations.

•

The owner is obliged to ensure that the device is operated in perfect working order only.

•

The device may only be used as intended (

“

area of application

”

).

•

You must periodically examine the safety equipment for their properly functioning condition.

•

The assembly instructions and/or operating instructions are always readily available at the location
where the device is being used, are complete and are in legible condition.

•

These persons are regularly instructed in all applicable questions regarding occupational safety
and environmental protection and are knowledgeable regarding the assembly instructions and/or
operating instructions and, especially, are familiar with the safety instructions contained therein.

•

All safety and warning notices attached to the device are never removed and remain legible.

2.9

Employment of external personnel

Maintenance and service work are frequently carried out by external employees who often do not
recognize the speci

ﬁ

c situations and the thus resulting dangers.These persons must be comprehen-

sively informed about the hazards in their area of activity.
You must monitor their working methods in order to intervene in good time if necessary.

Assembly instructions

ECblue

Safety instructions

L-BAL-F065-GB 1617 Index 004

Part.-No. 00702801-GB

7/28

171

«
...
169
170
171
172
173
...
»

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1PH818

Бренд: Vascat Страницы: 9

Бренд: Thermador Страницы: 20

Бренд: Lycoming Страницы: 83

Бренд: Kubota Страницы: 47

Бренд: Kubota Страницы: 181

Бренд: Stober Страницы: 48

Бренд: Baumuller Страницы: 26

Бренд: Baumuller Страницы: 33

Бренд: Johnson Страницы: 56

Бренд: Golden Eagle Страницы: 11

Бренд: Continental Refrigerator Страницы: 128

Бренд: Briggs & Stratton Страницы: 10

Бренд: Mitsubishi Страницы: 83

Бренд: Oemer Страницы: 97

Бренд: Parker Страницы: 44

Бренд: Parker Страницы: 116

Бренд: Man Страницы: 50

Бренд: Fagor Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды