Siemens 1PH818 Скачать руководство пользователя страница 152 | Manualshive

Страница: 152 / 198

Siemens 1PH818 Скачать руководство пользователя страница 152

Service Instructions NFF

Stromag Dessau

IP 66

safety in motion

Electromagnetic Double Face Spring – Applied Brake

01.06.2009

11

6

Initial setting into service

(Single parts with item designation as per chap. 4.1)

Before the initial setting into service, the following test measures are necessary:
• As the new friction lining does not yet dispose of optimum friction characteristics, some

electric releases have to be carried - out to smooth the friction face pinpoints.

• The electric connection values on the nameplate (73), see chap. 1.1, must comply with the

values at site

• The brake must be undamaged, i.e. it must not have any damage generated during

transportation, stocking, etc.

• The prescribed service conditions (chap. 7.1) must comply with those ones at site
• Not only the emergency manual release as per chap. 4.3 but also the hand lever emergency

release as per chap. 4.4 or 9.3 must not be active.

7 Operation

Notwithstanding any instructions given below, operation of the brake must

always comply with local mandatory safety and accident prevention rules. Compliance with
these rules shall be ensured by the user.

7.1 Operating

conditions

The operating conditions to be maintained for a faultless operation of the brake are given below:

-

The operating temperature should not be below

–30°C

and not above

+50°C

.

-

In the case of higher and/or lower ambient temperatures, please contact our after-sales
service (for address see Chapter 10.3).

-

Air humidity may be 100%.

152

«
...
150
151
152
153
154
...
»

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды