Siemens 1PH818 Скачать руководство пользователя страница 134

Страница: 134 / 198

Applications
The above-mentioned tightening torques apply for the following applications:
● Case A

Applies to electrical connections in which the permissible torque is normally limited by the

bolt materials and/or the current carrying capacity of the insulators, with the exception of

the busbar connections in case B.

● Case B

Applies to bolts screwed into components made from materials with lower property class

(e. g. aluminum) and to bolts with property class 8.8 according to ISO 898-1.

● Case C

Applies to bolts with property class 8.8 or A4-70 according to ISO 898-1, however only to

bolts screwed into components made from materials with higher property class, e.g. cast

iron, steel or cast steel.

Note
Non-standard tightening torques
Different tightening torques for electrical connections and bolted connections for parts with

flat seals or insulating parts are specified in the relevant sections and drawings.

Technical specifications
B.1 Tightening torques for screw and bolt connections

SIMOTICS M-1PH8 1PH818., 1PH822.

134

Operating Instructions 07/2016

Содержание 1PH818







































































































































































































Результаты поиска

Содержание 1PH818

Отзывы:

Siemens 1PH818, Инструкция по эксплуатации и установке, Страница: 134 / 198

Результаты поиска

Содержание 1PH818

Отзывы: