Siemens 1PH818 Скачать руководство пользователя страница 80

Страница: 80 / 198

6.4.5

Connecting the temperature sensor

● The temperature sensor is connected to the signal connector together with the speed

encoder signal.

● For the version without speed encoder, the temperature sensor is connected at the terminal

strip.

● The motor has a reserve temperature sensor, which is also connected at the auxiliary

terminal strip. Reconnect the temperature sensor as needed, e.g. if the previous

temperature sensor fails.

WARNING

Risk of electric shock
The insulation of the temperature sensors for the winding monitoring with respect to the

winding is implemented according to the requirements for basic insulation. The temperature

sensor connections are located in terminal boxes, safe to touch - and have no protective

separation. This is the reason that in the case of a fault, a hazardous voltage can be present

at the measuring sensor cable. When touched, this can result in death, severe bodily injury

and material damage.
● When connecting the temperature sensor to external temperature monitoring devices,

when required, apply additional measures to fully comply with the requirements set out in

IEC 60664-1 or IEC 61800-5-1 "Hazard due to electric shock".

6.4.6

Connecting to a converter

Selecting and connecting the cable

● Use Motion Connect cables or symmetrically constructed, shielded cables to connect the

motor to a converter. The cable shielding, made up of as many strands as possible, must

have good electrical conductivity. Braided shields made of copper or aluminum are well

suited.

● The shield is connected at both ends, at the motor and converter. Keep unshielded cable

ends as short as possible.

● In order to ensure that high-frequency currents are efficiently discharged, provide a 360°

contact through a large surface area at the converter and at the motor. Use for instance,

EMC glands at the cable entries.

Electrical connection
6.4 Auxiliary circuits

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

Содержание 1PH818







































































































































































































Результаты поиска

Содержание 1PH818

Отзывы:

Похожие инструкции для 1PH818

Бренды по названию

Популярные бренды

Siemens 1PH818, Инструкция по эксплуатации и установке

Результаты поиска

Содержание 1PH818

Отзывы:

Похожие инструкции для 1PH818

Бренды по названию

Популярные бренды