Siemens 1PH818 Скачать руководство пользователя страница 111

Страница: 111 / 198

To remove the spent grease, proceed as follows:
1. Remove the transmission element.
2. Remove the spent grease:

– At the DE, unscrew the outer bearing cover and empty the spent grease from the outer

bearing cover.

– At the NDE, remove the cover of the speed sensor and the cover of the spent grease

chamber. Empty the spent grease chamber.

Note
For types 1PH818. and 1PH822., you must remove the fan before removing the speed

encoder cover. At the NDE, remove the fan and then the speed encoder cover.

9.2.6.6

Maintaining the cooling water system

The cooling water pipe system, made of high-grade steel, is maintenance-free if the required

coooling water quality (Page 29) is maintained.

Maintenance

9.2 Inspection and maintenance

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

111

Содержание 1PH818







































































































































































































Результаты поиска

Содержание 1PH818

Отзывы:

Похожие инструкции для 1PH818

Бренды по названию

Популярные бренды

Siemens 1PH818, Инструкция по эксплуатации и установке

Результаты поиска

Содержание 1PH818

Отзывы:

Похожие инструкции для 1PH818

Бренды по названию

Популярные бренды