Siemens 1PH818 Скачать руководство пользователя страница 24

Страница: 24 / 198

Underwriters Laboratories
The SIMOTICS motor series generally complies with UL and cUL requirements as component

of motor applications - and is correspondingly listed. Specifically developed motors and

functions are the exceptions in this case. Here, it is important that you carefully observe the

contents of the quotation and that there is a cUL mark on the rating plate (nameplate)!

Quality management system
Siemens AG employs a quality management system that meets the requirements of ISO 9001

and ISO 14001.

Certificates that can be downloaded
You can download certificates for the SIMOTICS motor series at the following link:
Certificates (

https://support.industry.siemens.com/cs/ww/en/ps/13358/cert

)

Drive

The motor speed is controlled using a converter.

NOTICE
Destruction of the machine when operated directly from the line supply
The machine will be destroyed if it is directly connected to the line supply. Only operate the

machine using a converter.

Types of construction

The motor is available in the following basic types of construction and further optional types

of construction with additional application possibilities.

Table 3-3

Types of construction

Basic types of construction

Other applications in construction type

IM B3

IM B6, IM B7, IM B8, IM V6

IM V15

IM V5

IM B35

IM B5, IM V3, IM V35

The machine is supplied with two assembled lifting eyes. For IM V5 and IM V15 types of

construction with "shaft extension pointing downward", the machine is equipped with two

additional Vario eye bolts.

Description

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

Содержание 1PH818







































































































































































































Результаты поиска

Содержание 1PH818

Отзывы:

Похожие инструкции для 1PH818

Бренды по названию

Популярные бренды

Siemens 1PH818, Инструкция по эксплуатации и установке

Результаты поиска

Содержание 1PH818

Отзывы:

Похожие инструкции для 1PH818

Бренды по названию

Популярные бренды