Siemens 1PH818 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 198

background image

● When lifting the machine, refer to the information on the lifting plate.

– Comply with the specified spreading angles.
– Do not exceed the maximum lifting acceleration and lifting speed specified on the lifting

plate. Lift the machine without jerking it.

Acceleration a ≤ 0.4 g (≈ 4 m/s

2

)

Velocity v ≤ 20 m/min

● Use only the load carrying device on the stator frame for lifting.

WARNING

Transport for a different type of construction
If you do not transport or lift the machine in a position appropriate for its construction, the

machine can tip, slip into the lifting equipment or fall down. This can result in death, serious

injury or material damage.
● Use only the load carrying device on the stator frame for lifting.
● Use the load carrying device appropriate for the machine position.
● Use suitable rope guiding or spreading devices. The weight of the machine is shown on

the rating plate.

WARNING

Transport if the center of gravity is not at the center.
If the center of gravity of a load is not located centrally between the attachment points, the

motor can tip over or slip out of the lifting equipment and fall when it is being transported or

lifted. This can result in death, serious injury or material damage.
● Comply with the handling instructions on the machine when transporting it.
● Be aware of the possibility of different loads on the sling ropes or lifting straps and the

carrying capacity of the lifting equipment.

● Always take account of the center of gravity when transporting or lifting the motor. If the

center of gravity is not located centrally between the attachment points, then position the

hoisting hook above the center of gravity.

Note
Place the machine in a secure and raised position
In order to obtain easy and safe access to the underside of the machine, place it in a secure

and raised position.

DANGER

Standing under suspended loads
If the lifting gear or load handling attachments were to fail, the machine could fall. This can

result in death, serious injury or material damage.
Never remain under or in the immediate vicinity of the machine when it is raised.

Mounting

5.2 Lift the machine to where it will be mounted and position it

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

57

«
...
55
56
57
58
59
...
»

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1PH818

VLT OneGearDrive

Бренд: Danfoss Страницы: 44

VLT OneGearDrive

Бренд: Danfoss Страницы: 21

Бренд: Danfoss Страницы: 20

Бренд: Ibiza Страницы: 3

Бренд: Aerotech Страницы: 59

Vanguard 540000 Series

Бренд: Briggs & Stratton Страницы: 32

Бренд: Exalto Страницы: 28

HOME MOTION Roll Up 28 WT

Бренд: SOMFY Страницы: 10

Бренд: Kohler Страницы: 109

Бренд: Champion Power Equipment Страницы: 20

Бренд: Chris-Craft Страницы: 39

Бренд: Deutz Страницы: 257

Бренд: Daedong Страницы: 66

Бренд: Superior Страницы: 114

Бренд: Hitachi Страницы: 41

Бренд: Hitachi Страницы: 1037

Бренд: Hitachi Страницы: 1104

Бренд: Yamaha Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды