Siemens 1PH818 Скачать руководство пользователя страница 104

Страница: 104 / 198

NOTICE
Deviations from the normal state
If you detect any defects or malfunctions during the inspection, you must rectify them

immediately. They may otherwise cause damage to the machine.

9.2.4

Regreasing intervals

NOTICE
Damage to roller bearings
The regreasing intervals for roller bearings are different from the servicing intervals for the

machine. Failure to regrease the rolling-contact bearings at the specified intervals can result

in them sustaining damage.
● Comply with the regreasing intervals for roller bearings. The regreasing intervals are

specified on the lubricant plate.

9.2.5

Changing bearings when using permanently lubricated rolling-contact bearings

The replacement of the permanently lubricated roller bearing is determined by the number of

operating hours and is required around every three years.

9.2.6

Maintenance

When carrying out any work on the machine, observe the general safety instructions

(Page 13) and the specifications contained in EN 50110‑1 regarding safe operation of electrical

equipment.

9.2.6.1

Measuring the insulation resistance during the course of maintenance work

Measuring the insulation resistance and polarization index (PI) provides information on the

condition of the machine. It is therefore important to check the insulation resistance and the

polarization index at the following times:
● Before starting up a machine for the first time
● After an extended period in storage or downtime
● Within the scope of maintenance work

Maintenance
9.2 Inspection and maintenance

SIMOTICS M-1PH8 1PH818., 1PH822.

104

Operating Instructions 07/2016

Содержание 1PH818







































































































































































































Результаты поиска

Содержание 1PH818

Отзывы:

Бренды по названию

Популярные бренды

Siemens 1PH818, Инструкция по эксплуатации и установке

Результаты поиска

Содержание 1PH818

Отзывы:

Бренды по названию

Популярные бренды