Siemens 1PH818 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 198

background image

● All fixing screws, connection elements, and electrical connections have been tightened to

the specified tightening torques.

● The operating conditions match the data provided in accordance with the technical

documentation, such as degree of protection, ambient temperature, etc..

● Moving parts such as the coupling move freely.
● All touch protection measures for moving and live parts have been taken.

● If the second shaft extension is not in use, its feather key is secured to prevent it from being

thrown out, and cut back to roughly half its length if the rotor has balancing type "H"

(standard type). The unused shaft extension is covered and protected against accidental

contact.

● The rotor can spin without coming into contact with the stator.
● The bearing insulation is not bridged.

Electrical connection
● The grounding and equipotential bonding connections have been made correctly.
● The machine is connected so that it rotates in the direction specified.
● Appropriately configured control and speed monitoring functions ensure that the motor

cannot exceed the permissible speeds specified in the technical data. For this purpose,

compare the data on the rating plate or, if necessary, the system-specific documentation.

● The minimum insulation resistance values are within tolerance.
● Minimum air clearances have been maintained.
● Any supplementary motor monitoring devices and equipment have been correctly

connected and are functioning correctly.

● All brakes and backstops are operating correctly.
● At the monitoring devices, the values for "Warning" and "Shutdown" are set.

● Appropriately configured control and speed monitoring functions ensure that the the

permissible speeds specified on the rating plate cannot be exceeded.

● Any supplementary motor monitoring devices and equipment have been correctly

connected and are fully functional.

Converter operation
● If the design of the motor requires connection to a particular converter type, the rating plate

will contain corresponding additional information.

● The converter is correctly parameterized. The parameterization data is specified on the

rating plate of the machine. Information about the parameters is available in the operating

instructions for the converter.

● Any supplementary motor monitoring devices and equipment have been correctly

connected and are functioning correctly.

Commissioning
7.3 Checks to be carried out prior to commissioning

SIMOTICS M-1PH8 1PH818., 1PH822.

86

Operating Instructions 07/2016

«
...
84
85
86
87
88
...
»

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1PH818

Бренд: Subaru Страницы: 52

Бренд: Quick Fuel Technology Страницы: 5

MaxxForce 3.2H Euro V

Бренд: Navistar Страницы: 116

Бренд: Man Страницы: 42

Бренд: Man Страницы: 48

Бренд: O.S. engine Страницы: 4

Бренд: Toyama Страницы: 44

Бренд: Stark Страницы: 14

Бренд: Sears Страницы: 12

Бренд: Superrollo Страницы: 68

Бренд: Rotax Страницы: 84

Бренд: Rotax Страницы: 166

Бренд: Perkins Страницы: 54

Бренд: Black Bruin Страницы: 70

Бренд: Volvo Penta Страницы: 40

Бренд: Volvo Penta Страницы: 48

Бренд: Volvo Penta Страницы: 76

Бренд: Volvo Penta Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды