Siemens 1PH818 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 198

background image

4.13

Transport and storage

When carrying out any work on the machine, observe the general safety instructions

(Page 13) and the specifications contained in EN 50110‑1 regarding safe operation of electrical

equipment.

4.13.1

Checking the delivery

Checking the delivery for completeness

The drive systems are put together on an individual basis. When you take receipt of the

delivery, please check immediately whether the items delivered are in accordance with the

accompanying documents. Siemens will not accept any claims relating to items missing from

the delivery and which are submitted at a later date.
● Report any apparent transport damage to the delivery agent immediately. Never

commission a damaged motor.

● Report any apparent defects/missing components to the appropriate Siemens office

immediately.

These safety instructions are part of the scope of supply; keep them in a location where they

can be easily accessed.

4.13.2

Lifting and transportation

To safely lift and transport the machine, the following requirements must be met:
● Personnel operating cranes and fork-lift trucks must be appropriately qualified.
● If the motor is packed, depending on the weight, size and on-site conditions, lift crates and

transport frames using a fork-lift truck or a crane with slings. Use a crane or fork-lift truck

suitable for the load.

● When lifting the machine, use only approved and undamaged sling guides and spreaders

of sufficient rated capacity. Check the lifting equipment prior to its use. The weight of the

machine is shown on the rating plate.

● When lifting the machine, refer to the information on the lifting plate.

– Comply with the specified spreading angles.
– Do not exceed the maximum lifting acceleration and lifting speed specified on the lifting

plate. Lift the machine without jerking it.

Acceleration a ≤ 0.4 g (≈ 4 m/s

2

)

Velocity v ≤ 20 m/min

● Use only the load carrying device on the stator frame for lifting.

Preparations for use
4.13 Transport and storage

SIMOTICS M-1PH8 1PH818., 1PH822.

36

Operating Instructions 07/2016

«
...
34
35
36
37
38
...
»

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1PH818

Vanguard 290000

Бренд: Briggs & Stratton Страницы: 68

Бренд: Kohler Страницы: 4

Бренд: Yamaha Страницы: 30

Бренд: Lister Petter Страницы: 81

Бренд: Lister Petter Страницы: 100

Бренд: Winterthur Gas Страницы: 547

Бренд: Yanmar Страницы: 231

Бренд: Detroit Diesel Страницы: 22

Бренд: Detroit Diesel Страницы: 224

Бренд: panthera Страницы: 12

MINIMAX 3TNM72-GGE

Бренд: Yanmar Страницы: 2

HSK35,40, HSSK50

Бренд: Tecumseh Страницы: 8

120000 Intek I/C 850 Series

Бренд: Briggs & Stratton Страницы: 28

CORTINO DT72LE Series

Бренд: YOODA Страницы: 7

Бренд: MTU Страницы: 195

116 - V1.1 ASSEMBLY EXHAUSTS 3207I-3208I-3210

Бренд: MVVS Страницы: 1

Бренд: Franklin Страницы: 8

Бренд: Franklin Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды