manualshive.com logo in svg

Siemens 1PH818, Инструкция по эксплуатации и установке

Поделиться
Скачать
Siemens 1PH818 Скачать руководство пользователя страница 98

Table 8-2

Electrical faults   

↓ Motor fails to start
 

↓ Motor accelerates sluggishly
 

↓ Humming noise when starting
 

↓ Humming noise in operation
 

↓ High temperature rise during no-load operation
 

↓ High temperature rise under load
 

↓ High temperature rise of individual winding sections
 

Possible causes of faults

Remedial measures

X

 

 

 

 

X

  Rotor (partially) demagnetized

Contact the Service Center.

X

X  

X  

X  

Overload

Reduce the load.

X  

 

 

 

 

 

Interruption of a phase in the feeder 

cable

Check the frequency converters and feeder cables.

 

X

X

X  

X  

Interrupted phase in the feeder ca‐

ble after switching on

Check the frequency converters and feeder cables.

 

X

X

X  

 

X Winding short circuit or inter-phase 

short circuit in stator winding

Determine the winding resistances and insulation re‐

sistances. Contact the Service Center.

 

 

 

 

X  

 

Converter output voltage too high, 

frequency too low

Check the settings at the frequency converter and 

perform the automatic motor identification.

 

 

 

 

X

X  

Cooling water not connected
Cooling water supply switched off
Water connection / pipes defective

Check the cooling water connection. Switch on the 

cooling water supply.
Find the leak and seal it. Contact the Service Center.

 

 

 

 

X

X  

Cooling water flow rate too low
Inlet temperature too high

Increase the cooling water flow.
Set the correct upstream temperature.

8.10.4

Mechanical faults

Table 8-3

Mechanical faults   

↓ Grinding noise
 

↓ Radial vibrations
 

↓ Axial vibrations
 

Possible causes of faults

Remedial measures

X  

 

Rotating parts are grinding

Establish the cause and realign the parts.

 

X  

Rotor not balanced

Contact the Service Center.

 

X  

Rotor out of true, shaft bent

Contact the Service Center.

 

X

X Poor alignment

Align the machine set and check the coupling. 

1)

 

X  

Coupled machine not balanced

Rebalance the coupled machine.

 

 

X Shocks from coupled machine

Examine the coupled machine.

 

X

X Resonance with the foundation

Stabilize the foundation after prior discussion.

 

X

X Changes in foundation

Determine the cause of the changes and, if necessa‐

ry, rectify. Realign the machine.

1) 

Take into account possible changes which may occur during overheating.

Operation
8.10 Faults

SIMOTICS M-1PH8  1PH818., 1PH822.

98

Operating Instructions 07/2016

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды