manualshive.com logo in svg

Siemens 1PH818, Инструкция по эксплуатации и установке

"Siemens 1PH818" - мощный электродвигатель, предназначенный для применения в различных индустриальных секторах. Вы можете скачать бесплатно Руководство по эксплуатации и инструкции по установке на manualshive.com. Получите подробную информацию о данном изделии и его функциях, чтобы использовать его эффективно и безопасно.

Поделиться
Скачать
background image

Shaft extensions with feather key 

To maintain the balancing quality, you have the following options:
● If the transmission element is shorter than the feather key with balancing type "H", then you 

must machine off the section of feather key protruding from the shaft contour and 

transmission element in order to maintain the balance quality.

● If the output element is mounted up to the shaft shoulder for motors with full-key balancing 

"F", or if the output element is longer than the motor shaft extension, then when balancing 

the coupling or belt pulley, take into account that the feather key does not completely fill 

the slot in the hub.

WARNING

The feather key can fall out  
The feather keys are only locked against falling out during shipping. If a machine with two 

shaft extensions does not have an output element on one shaft extension, the feather key 

can fall out during operation. 
Death or serious injury can result.
● Do not operate the machine unless the transmission elements have been pulled on.
● On shaft extensions without output element, make sure that the feather key cannot fall 

out and shorten it by approximately half for balance type "H".

Note
Type of balancing
In the case of shaft extensions with feather keys, the type of balancing is also included on the 

rating plate next to the CE mark.

5.2.5

Lifting and transporting the machine

To safely lift and transport the machine, the following requirements must be met: 
● Personnel operating cranes and fork-lift trucks must be appropriately qualified.
● If the motor is packed, depending on the weight, size and on-site conditions, lift crates and 

transport frames using a fork-lift truck or a crane with slings. Use a crane or fork-lift truck 

suitable for the load.

● When lifting the machine, use only approved and undamaged sling guides and spreaders 

of sufficient rated capacity. Check the lifting equipment prior to its use. The weight of the 

machine is shown on the rating plate.

Mounting
5.2 Lift the machine to where it will be mounted and position it

SIMOTICS M-1PH8  1PH818., 1PH822.

56

Operating Instructions 07/2016

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1PH818

Jabiru 2200 Instruction And Maintenance Manual preview
2200
Бренд: Jabiru Страницы: 116
IAME Parilla Norswift 60cc User Manual preview
Parilla Norswift 60cc
Бренд: IAME Страницы: 9
IAME Parilla Norswift 60cc Assembly Instructions And User'S Manual preview
Parilla Norswift 60cc
Бренд: IAME Страницы: 35
CG TAO-659 Maintenance Handbook preview
TAO-659
Бренд: CG Страницы: 45
Perkins 1104D Operation And Maintenance Manual preview
1104D
Бренд: Perkins Страницы: 112
Team Orion Vortex M Manual preview
Vortex M
Бренд: Team Orion Страницы: 2
Toyama TDE110TB-XP Owner'S Manual preview
TDE110TB-XP
Бренд: Toyama Страницы: 44
IAME EASY-KART 100cc Assembly Instructions And User'S Manual preview
EASY-KART 100cc
Бренд: IAME Страницы: 35
Mafell FM 1000 Original Operating Instructions preview
FM 1000
Бренд: Mafell Страницы: 166
Toro AC-1 Service Manual preview
AC-1
Бренд: Toro Страницы: 96
HIFEI Technology ESC-10A Instruction preview
ESC-10A
Бренд: HIFEI Technology Страницы: 2
Chicago Pneumatic 2H410-350-ATEX Safety Information Manual preview
2H410-350-ATEX
Бренд: Chicago Pneumatic Страницы: 100
DETROIT 471952 Operator'S Manual preview
471952
Бренд: DETROIT Страницы: 84
O.S. engine GT55 Owner'S Instruction Manual preview
GT55
Бренд: O.S. engine Страницы: 18
O.S. engine MAX 140RX FI Owner'S Instruction Manual preview
MAX 140RX FI
Бренд: O.S. engine Страницы: 24
DANA BREVINI D 072 Series Installation And Maintenance Manual preview
BREVINI D 072 Series
Бренд: DANA Страницы: 58
DANA BREVINI M Series Installation And Maintenance Manual preview
BREVINI M Series
Бренд: DANA Страницы: 40
Volvo Penta V6-240 Operator'S Manual preview
V6-240
Бренд: Volvo Penta Страницы: 176

Бренды по названию

Популярные бренды

Загрузить еще бренды