Siemens 1PH818 Скачать руководство пользователя страница 44

Страница: 44 / 198

Condensation

Condensation can collect in the machine as a result of sharp fluctuations in ambient

temperature, exposure to direct sunlight, high levels of humidity in the storage location or

intermittent operation/variations in load during operation.

NOTICE
Damage due to condensation
If the stator winding is damp, its insulation resistance is reduced. This results in voltage

flashovers that can destroy the winding. Condensation can also cause rusting inside the

machine.

Water drain holes (option L12)

Depending on the order concerned, the bearing shields at the DE and NDE are equipped with

water drainage holes in the foot area and opposite the regreasing system. Make sure that the

condensation can always drain away freely.
● Shaft heights 180 and 225: The plug that has been inserted into the water drainage holes

allows the condensation to drain away. Do not remove the plug, otherwise the machine's

degree of protection will be affected.

● Shaft height 280: There are no plugs in the water drain holes. The water must be able to

drain away freely.

NOTICE
Water drain holes
The water drain holes only function when the motor is mounted horizontally for types of

construction IM B3, IM B35 and IM B5.

Preparations for use
4.13 Transport and storage

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

Содержание 1PH818







































































































































































































Результаты поиска

Содержание 1PH818

Отзывы:

Бренды по названию

Популярные бренды

Siemens 1PH818, Инструкция по эксплуатации и установке

Результаты поиска

Содержание 1PH818

Отзывы:

Бренды по названию

Популярные бренды