Siemens 1PH818 Скачать руководство пользователя страница 29

Страница: 29 / 198

Preparations for use

Good planning and preparation of machine applications are essential in terms of keeping

installation simple and avoiding errors, ensuring safe operation, and allowing access to the

machine for servicing and corrective maintenance.
This chapter outlines what you need to consider when configuring your plant in relation to this

machine and the preparations you need to make before the machine is delivered.

4.1

Safety-related aspects to consider when configuring the plant

A number of residual risks are associated with the machine. These are described in the chapter

titled "Safety information" (Page 13) and in related sections.
Take appropriate safety precautions (covers, barriers, markings, etc.) to ensure the machine

is operated safely within your plant.

4.2

Observing the operating mode

Observe the machine's operating mode. Use a suitable control system to prevent overspeeds,

thus protecting the machine from damage.

4.3

Cooling water quality for water-cooled motors

The values specified for the cooling water correspond to the requirements for a closed cooling

circuit. Not all of the specified concentrations will occur in the cooling water at the same time.

A filter can be used to ensure smooth operation; the grade of filtration should not exceed

100 μm.

Cooling water specification

Table 4-1

Cooling water specification

Constituent

Value

pH value

6.0 … 9.0

Total hardness

< 170 ppm

Conductivity

< 500 μS/cm

Chloride ions

< 40 ppm

Sulfate ions

< 50 ppm

Nitrate ions

< 50 ppm

Dissolved solids

< 340 ppm

Max. grain size

< 100 μm

SIMOTICS M-1PH8 1PH818., 1PH822.

Operating Instructions 07/2016

Содержание 1PH818







































































































































































































Результаты поиска

Содержание 1PH818

Отзывы:

Похожие инструкции для 1PH818

Бренды по названию

Популярные бренды

Siemens 1PH818, Инструкция по эксплуатации и установке

Результаты поиска

Содержание 1PH818

Отзывы:

Похожие инструкции для 1PH818

Бренды по названию

Популярные бренды