Siemens 1PH818 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 198

background image

5.1.2

Insulation resistance and polarization index

Measuring the insulation resistance and polarization index (PI) provides information on the

condition of the machine. It is therefore important to check the insulation resistance and the

polarization index at the following times:
● Before starting up a machine for the first time
● After an extended period in storage or downtime
● Within the scope of maintenance work
The following information is provided regarding the state of the winding insulation:
● Is the winding head insulation conductively contaminated?
● Has the winding insulation absorbed moisture?
As such, you can determine whether the machine needs commissioning or any necessary

measures such as cleaning and/or drying the winding:
● Can the machine be put into operation?
● Must the windings be cleaned or dried?
Detailed information on testing and the limit values can be found here:
"Testing the insulation resistance and polarization index" (Page 50)

5.1.3

Testing the insulation resistance and polarization index

WARNING

Hazardous voltage at the terminals
During and immediately after measuring the insulation resistance or the polarization index

(PI) of the stator winding, hazardous voltages may be present at some of the terminals.

Contact with these can result in death, serious injury or material damage.
● If any power cables are connected, check to make sure line supply voltage cannot be

delivered.

● Discharge the winding after measurement until the risk is eliminated, e.g. using the

following measures:
– Connect the terminals with the ground potential until the recharge voltage drops to a

non-hazardous level

– Attach the connection cable.

Measure the insulation resistance

1. Before you begin measuring the insulation resistance, please read the operating manual

for the insulation resistance meter you are going to use.

2. Make sure that no power cables are connected.

Mounting
5.1 Preparing for installation

SIMOTICS M-1PH8 1PH818., 1PH822.

50

Operating Instructions 07/2016

«
...
48
49
50
51
52
...
»

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1PH818

Vanguard 290000

Бренд: Briggs & Stratton Страницы: 68

Vanguard EFI 380000

Бренд: Briggs & Stratton Страницы: 100

Бренд: ZF Страницы: 80

Бренд: Habasit Страницы: 60

Бренд: Lycoming Страницы: 38

Бренд: Lister Petter Страницы: 60

Бренд: DLE Страницы: 4

Бренд: DLE Страницы: 4

Бренд: PYD Electrobombas Страницы: 36

Allen-Bradley TLP-SSN-F046

Бренд: Rockwell Automation Страницы: 8

Бренд: Yanmar Страницы: 112

Бренд: Sabre Страницы: 30

Бренд: Lin Engineering Страницы: 23

Бренд: 3W Страницы: 20

Бренд: YASKAWA Страницы: 177

Бренд: Nanni Страницы: 64

Бренд: Odyssey Страницы: 14

Volt Electric Drive

Бренд: Native Watercraft Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды