MerCruiser QSD 2.0 Скачать руководство пользователя

Страница: 1 / 135

QSD 2.0 Diesel Engine Sterndrive Models

*8M0057081*

90-8M0057081 311

Declaration of Conformance—Cummins MerCruiser Diesel

This sterndrive or inboard engine when installed in accordance with Cummins MerCruiser Diesel instructions complies with

the requirements of the following directives by meeting the associated standards, as amended:

Recreational Craft Directive 94/25/EC; 2003/44/EC

Applicable Requirement

Standards Applied

Handling characteristics (A.4)

ISO 8665

Inboard engine (A.5.1.1)

ISO 15584; ISO 10088; ISO 7840; ISO 10133

Steering system (A.5.4)

Applicable portions of: ISO 10592, ISO 8848 and ABYC

P‑17

Exhaust emission requirements (B.2)

ISO 8178

Owner’s manual (B.4)

ISO 8665

Noise emission levels (C.1) (sterndrive CE marked

products only)

ISO 14509

Cummins MerCruiser Diesel declares that our sterndrive or inboard engines without integral exhaust, when installed in a

recreational craft in accordance with the manufacturer's supplied instructions will meet the exhaust emissions requirements

of the directive mentioned above. This engine must not be put into service until the recreational craft in which it is to be

installed has been declared in conformity, if so required, with the relevant provision of the directive.

Electromagnetic Compatibility Directive 89/336/EC, 92/31/EEC and 93/68/EEC

Generic emission standard

EN 50081‑1

Generic immunity standard

EN 50082‑1

Vehicles, boats and internal combustion engine driven

devices—radio disturbance characteristics

SAE J551 (CISPR 12)

Electrostatic discharge testing

EN 61000‑6‑2; EN 61000‑4‑2; EN61000‑4‑3

For specific information regarding exhaust or noise emissions and power declaration, please refer to the Declaration of

Conformity supplied with each Cummins MerCruiser Diesel engine.

This declaration is issued under the sole responsibility of Cummins MerCruiser Diesel.

Jim Kahlenbeck

Director of Engineering—Cummins MerCruiser Diesel, Charleston, South Carolina U.S.A.

Regulatory contact:

Engineering—Marine Emissions

Cummins MerCruiser Diesel

4500 Leeds Avenue

Charleston, South Carolina 29405

USA

(843) 745-1610

Identification Record

Please record the following information:

Engine Model and Horsepower

Engine Serial Number

Transom Assembly Serial Number (Sterndrive)

Gear Ratio

Sterndrive Unit Serial Number

Содержание QSD 2.0








































































































































Результаты поиска

Содержание QSD 2.0

Отзывы:

Похожие инструкции для QSD 2.0

Бренды по названию

Популярные бренды

MerCruiser QSD 2.0, Руководство пользователя

Результаты поиска

Содержание QSD 2.0

Отзывы:

Похожие инструкции для QSD 2.0

Бренды по названию

Популярные бренды