MerCruiser QSD 2.0 Скачать руководство пользователя

Страница: 45 / 135

Section 4 - Specifications

90-8M0057081

eng

MARCH 2011

Page 37

Coolant (Antifreeze)

NOTICE

Using propylene glycol antifreeze in the closed cooling system can damage the cooling system or the engine. Fill the closed

cooling system with an ethylene glycol antifreeze solution suitable to the lowest temperature to which the engine will be exposed.

Because diesel engines are high‑compression engines, they operate at higher operating temperatures. Therefore the closed

cooling system and engine, including related cooling passages, must remain as clean as possible to provide adequate engine

cooling. To ensure proper cooling, we recommend filling the closed cooled section of the cooling system with a low silicate formula

of ethylene glycol antifreeze in a solution with deionized water. A low silicate formula prevents the antifreeze from separating and

forming a silicate gelatin. This gelatin can block passages in the engine and heat exchanger, causing the engine to overheat.

Using deionized water instead of common tap water or softened water can prevent large mineral deposits from forming that restrict

the cooling system efficiency.
Mix the coolant, if it is not premixed, before adding it to the closed cooling system. Additives and inhibitors introduced into

acceptable coolant solutions will form a protective film on the internal passages and provide protection against internal cooling

system erosion.
Keep the closed cooling section filled year‑round with an acceptable coolant (antifreeze) solution. Do not drain the closed cooled

section for storage as this will promote rust formation on the internal surfaces. If the engine will be exposed to freezing

temperatures, ensure that the closed cooled section is filled with a properly mixed coolant (antifreeze) solution to protect the engine

and closed cooling system to the lowest temperature to which they will be exposed.

NOTE: Generally, we recommend using a 50/50 solution of coolant (antifreeze) and deionized, purified water. When operating

where seawater temperatures are greater than 32 °C ( 90 °F), you can use a 25/75 solution of coolant (antifreeze) and deionized,

purified water for improved cooling performance.

IMPORTANT: The coolant (antifreeze) used in these marine engines must be a solution of low silicate ethylene glycol containing

special additives and deionized, purified water. Using other types of engine coolant may cause fouling of the heat exchangers and

overheating of the engine. Do not combine different types of coolants without knowing that they are compatible. Refer to the coolant

manufacturer's instructions.
Some acceptable types of antifreeze and coolants are listed in the following table. See

Maintenance Schedules

for respective

change intervals.

Description

Availability

Part Number

Marine Engine Coolant

Quantity: 3‑3/4 liters, 1 U.S. Gallon

Europe only

92‑813054A2

Fleetguard Compleat with DCA4

Quantity: 3‑3/4 liters, 1 U.S. Gallon

Worldwide

Fleetguard Part Number: CC2825

Engine Oil

NOTICE

Discharge of oil, coolant, or other engine/drive fluids into the environment is restricted by law. Use caution not to spill oil, coolant,

or other fluids into the environment when using or servicing your boat. Be aware of the local restrictions governing the disposal

or recycling of waste, and contain and dispose of fluids as required.

To help obtain optimum engine performance and to provide maximum protection, the engine requires engine oil with a rating of

HD‑SAE‑API CG‑4 and CH‑4.
We strongly recommend the use of:

Description

Where Used

Part Number

Mercury 4‑ Cycle 15W40 Marine Engine Oil

Engine crankcase

92‑877695K1

This oil is a specially blended 15W40 oil with marine additives for all–temperature operation. It exceeds requirements for API CF‑2,

CF‑4, CG‑4 and CH‑4 oils.
Other recommended oils:

Содержание QSD 2.0








































































































































Результаты поиска

Содержание QSD 2.0

Отзывы:

Похожие инструкции для QSD 2.0

Бренды по названию

Популярные бренды

MerCruiser QSD 2.0, Руководство пользователя

Результаты поиска

Содержание QSD 2.0

Отзывы:

Похожие инструкции для QSD 2.0

Бренды по названию

Популярные бренды