MerCruiser QSD 2.0 Скачать руководство пользователя

Страница: 63 / 135

Section 5 - Maintenance

90-8M0057081

eng

MARCH 2011

Page 55

16. Push the filter element into the cover until it is locked. Listen for a click.

Engine coolant oil cooler

Seawater oil cooler

a -

Oil filter cover

b -

O‑ring

c -

Filter element

17. Install the cover with the new filter element into the oil filter housing. Turn the oil filter cover until the sealing surface contacts

the housing.

18. Tighten the cover to specification.

IMPORTANT: Overtightening the cover may cause an oil leak.

Engine Coolant Oil Cooler

Description

lb–in.

lb–ft

Engine oil filter housing cover

25.0

–

18.0

Seawater Oil Cooler

Description

lb–in.

lb–ft

Engine oil filter housing cover

22.5

–

16.0

19. Remove the oil fill cap and refill the engine with new oil. See

Filling

IMPORTANT: When refilling the engine with oil, always use the dipstick to determine how much oil is required.

20. Replace and secure the oil fill cap.
21. Start the engine and check for leaks.

Alpha Sterndrive Gear Lube

Sterndrive Gear Lube

NOTICE

Discharge of oil, coolant, or other engine/drive fluids into the environment is restricted by law. Use caution not to spill oil, coolant,

or other fluids into the environment when using or servicing your boat. Be aware of the local restrictions governing the disposal

or recycling of waste, and contain and dispose of fluids as required.

Checking

NOTE: The gear lube level will fluctuate during operation. The gear lube level should be checked with the engine cold, before

starting.

33986

Содержание QSD 2.0








































































































































Результаты поиска

Содержание QSD 2.0

Отзывы:

Похожие инструкции для QSD 2.0

Бренды по названию

Популярные бренды

MerCruiser QSD 2.0, Руководство пользователя

Результаты поиска

Содержание QSD 2.0

Отзывы:

Похожие инструкции для QSD 2.0

Бренды по названию

Популярные бренды