MerCruiser QSD 2.0 Скачать руководство пользователя страница 22

Страница: 22 / 135

Section 2 - Getting to Know Your Power Package

Page 14

90-8M0057081

eng

MARCH 2011

Switches

a -

Key switch

b -

Bilge blower switch (if equipped)

Reference

Switch

Function

Key switch

Has four positions.

"OFF."

In the "OFF" position, all electrical circuits are off and the

engine cannot be started. The engine is stopped when the key

switch is turned to the "OFF" position.

"ACC."

In the "ACC" position, any accessory connections to the

electrical circuits can be operated. The engine will not operate with

the key switch in the "ACC" position.

"ON."

In the "ON" position, all electrical circuits and instruments are

operational.

"START."

In the "START" position the engine can be started.

NOTE: The key can only be removed with the key switch in the "OFF"

position.

Bilge blower switch (if equipped)

Operates the bilge blower, if equipped

Start/Stop Panel

The start/stop panel allows the operator to start or stop an engine with the press of a single button. In dual engine applications,

each engine is controlled independently. For the start/stop panel to function, the key switch must be in the "ON" position.

28082

Dual engine start/stop panel, single engine similar

In single helm applications, the start/stop panel is optional.
In dual helm applications, a start/stop panel is optional at the main station and required at secondary stations. The ignition key

switch connector will be capped at helm 2.

24735

Содержание QSD 2.0








































































































































Результаты поиска

Содержание QSD 2.0

Отзывы:

Бренды по названию

Популярные бренды

MerCruiser QSD 2.0, Руководство пользователя

Результаты поиска

Содержание QSD 2.0

Отзывы:

Бренды по названию

Популярные бренды