manualshive.com logo in svg

MerCruiser QSD 2.0, Руководство пользователя

MerCruiser QSD 2.0 - дизельный двигатель с мощностью 115-170 л.с. Вы можете бесплатно скачать руководство пользователя на manualshive.com для получения подробной информации о настройке и обслуживании. Начните загрузку прямо сейчас и овладейте всеми возможностями этого надежного двигателя.

Поделиться
Скачать
background image

Section 1 - Warranty

90-8M0057081   

eng

  MARCH  2011

Page  5

•

Starter motors, armatures, or field coil assemblies, that are burned, or where lead is thrown out of the commutator

because of excessive cranking

•

Damage to the product from insufficient cooling water caused by blockage of the cooling system or water inlets

•

Damage caused by running the engine out of water

•

Damage resulting from mounting the power package too high on the transom

•

Damage as a result of operating the boat with the engine over trimmed

•

Damage caused by engines that do not reach maximum rated RPM because of vessel overloading

•

Labor not performed by a Cummins MerCruiser Diesel Authorized Repair Facility except when such a facility is

not available to perform the work required and prior factory approval has been given to have the work performed

at an alternate repair facility on an emergency basis

•

Expenses related to haul‑out, launch, or towing

•

Removal or replacement of boat partitions or other material in order to gain access to the product

•

Expenses related to delivering the product to a Cummins MerCruiser Diesel Authorized Dealer when reasonable

access is not provided to the product for warranty service

•

Expenses related to storage, telephone, rental, inconvenience, slip fees, insurance coverage, loan payments,

loss of time, loss of income, or any other type of incidental or consequential damages

 

Use of the product for racing or other competitive activity, or operating with a racing‑type lower unit at any time, even

by a previous owner of the product, voids the warranty.
 

No individual or entity, including Cummins MerCruiser Diesel authorized dealers, has been given authority by

Cummins MerCruiser Diesel to make any affirmation, representation, or warranty regarding the product, other than

those contained in this limited warranty, and if made, shall not be enforceable against Cummins MerCruiser Diesel.
 

DISCLAIMERS AND LIMITATIONS

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
EXPRESSLY DISCLAIMED. TO THE EXTENT THAT THEY CANNOT BE DISCLAIMED, THE IMPLIED
WARRANTIES ARE LIMITED IN DURATION TO THE LIFE OF THE EXPRESS WARRANTY. INCIDENTAL AND
CONSEQUENTIAL DAMAGES ARE EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. SOME
STATES/COUNTRIES DO NOT ALLOW FOR THE DISCLAIMERS, LIMITATIONS AND EXCLUSIONS
IDENTIFIED ABOVE. AS A RESULT, THEY MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH VARY FROM STATE TO STATE
AND COUNTRY TO COUNTRY.

Limited Warranty Against Corrosion (Worldwide)

What Is Covered

Cummins MerCruiser Diesel warrants that each new Alpha and Bravo sterndrive (Product) will not be

rendered inoperative as a direct result of corrosion for the period of time described below.

Duration of Coverage

This limited corrosion warranty provides coverage for three (3) years from either the date the product is first

sold, or the date on which the product is first put into service, whichever occurs first. For sterndrive models

with SeaCore, the warranty coverage is four (4) years from either the date the product is first sold, or the

date on which the product is first put into service, whichever occurs first. The repair and replacement of

parts, or the performance of service under this warranty does not extend the life of this warranty beyond its

original expiration date. Unexpired warranty coverage can be transferred to subsequent purchaser upon

proper re‑registration of the product. Warranty coverage is terminated for used product repossessed from

a retail customer, purchased at auction, from a salvage yard, or from an insurance company that obtained

the product as a result of an insurance claim.

Conditions That Must Be Met to Obtain Warranty Coverage

Содержание QSD 2.0








































































































































Отзывы:

Нет отзывов

Похожие инструкции для QSD 2.0

Warner ERS VAR10 SZ 2500 Service & Installation Manual preview
ERS VAR10 SZ 2500
Бренд: Warner Страницы: 16
Sachs SA 2-440 Repair Instructions preview
SA 2-440
Бренд: Sachs Страницы: 52
Raider 50 HP TLDI Owner'S Manual preview
50 HP TLDI
Бренд: Raider Страницы: 28
Yanmar 2YM15 Service Manual preview
2YM15
Бренд: Yanmar Страницы: 231
Stiga RS100 Workshop Manual preview
RS100
Бренд: Stiga Страницы: 65
New Holland E485C Service Manual preview
E485C
Бренд: New Holland Страницы: 31
Toyota 1981 2F Repair Manual preview
1981 2F
Бренд: Toyota Страницы: 78
quiko QK E3000 Use And Maintenance Manual preview
QK E3000
Бренд: quiko Страницы: 12
Nakanishi EM20-S6000 Operation Manual preview
EM20-S6000
Бренд: Nakanishi Страницы: 2
Nakanishi BMS-4020-MQL Series Operation Manual preview
BMS-4020-MQL Series
Бренд: Nakanishi Страницы: 24
Nanni Z4.205 Operator'S Manual preview
Z4.205
Бренд: Nanni Страницы: 98
Nice E Fit L Instructions And Warnings For Installation And Use preview
E Fit L
Бренд: Nice Страницы: 52
Inel YYGL35RP-10/17 Operating Instructions preview
YYGL35RP-10/17
Бренд: Inel Страницы: 3
Inel YYGL35RE-10/17 Operating Instructions preview
YYGL35RE-10/17
Бренд: Inel Страницы: 4
de Wijs 2007 User Manual preview
2007
Бренд: de Wijs Страницы: 13
DANA 4360-79 Parts List preview
4360-79
Бренд: DANA Страницы: 3
Team Orion VST2 Pro Instruction Manual preview
VST2 Pro
Бренд: Team Orion Страницы: 2
Parker 892 Series Owner'S Manual preview
892 Series
Бренд: Parker Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды