MerCruiser QSD 2.0 Скачать руководство пользователя

Страница: 26 / 135

Section 2 - Getting to Know Your Power Package

Page 18

90-8M0057081

eng

MARCH 2011

Remote Controls

Your boat may be equipped with a Mercury Precision Parts or Quicksilver remote control. All controls may not have all features

shown. Consult your dealer for a description or demonstration of your remote control.

Panel Mount Features

a -

Neutral lock button

b -

Throttle–only button

c -

Lanyard stop switch

d -

Control handle tension adjustment screw

e -

Control handle

f -

Trim/tilt button

Neutral Lock Button.

Prevents accidental shift and throttle engagement. Neutral lock button must be pushed into move the control

handle out of neutral.

Throttle–Only Button.

Allows engine throttle advancement without shifting the engine. This is done by disengaging the shift

mechanism from the control handle. The throttle–only button can be depressed only when the remote control handle is in the

neutral position, and should only be used to assist in starting the engine.

Lanyard Stop Switch.

Provides an emergency engine shut down if the boat operator (when attached to the lanyard) moves far

enough away from the operator's position to pull the lanyard key that activates the engine stop switch.

Control Handle.

Operation of the shift and throttle are controlled by the movement of the control handle. Push the control handle

forward from neutral with a quick, firm motion to the first detent for forward gear. Continue pushing forward to increase speed. Pull

the control handle back from neutral with a quick, firm motion to the first detent for reverse gear and continue pushing back to

increase speed.

Control Handle Tension Adjustment Screw (not visible).

This screw is used to adjust the effort required to move the remote

control handle. Refer to the instructions provided with the remote control for complete adjustment instructions.

Trim/Tilt Button.

Refer to

Power Trim

Console Mount Features

a -

Throttle–only button

b -

Control handle

c -

Power trim switch

d -

Trailer switch

mc77019-1

mc79503-1

Содержание QSD 2.0








































































































































Результаты поиска

Содержание QSD 2.0

Отзывы:

Похожие инструкции для QSD 2.0

Бренды по названию

Популярные бренды

MerCruiser QSD 2.0, Руководство пользователя

Результаты поиска

Содержание QSD 2.0

Отзывы:

Похожие инструкции для QSD 2.0

Бренды по названию

Популярные бренды