manualshive.com logo in svg

MerCruiser QSD 2.0, Руководство пользователя

Поделиться
Скачать
MerCruiser QSD 2.0 Скачать руководство пользователя страница 51

Section 5 - Maintenance

90-8M0057081   

eng

  MARCH  2011

Page  43

•

Do not telephone the dealer, service office, or the factory to attempt for them to diagnose a problem or to request the repair

procedure. It is difficult for them to diagnose a problem over the telephone.

Your local Cummins MerCruiser Diesel Authorized Repair Facility is there to service your power package. They have qualified

factory‑trained mechanics.
It is recommended you have the Cummins MerCruiser Diesel Authorized Repair Facility do periodic maintenance checks on your

power package. Have them winterize it in the fall and service it before the boating season. This will reduce the possibility of any

problems occurring during your boating season when you want trouble‑free boating pleasure.

General Inspection

Inspect your power package often and at regular intervals to help maintain its top operating performance and to correct potential

problems before they occur. The entire power package should be checked carefully, including all accessible engine parts.
1. Check for loose, damaged, or missing parts, hoses and clamps; tighten or replace as necessary.
2. Check electrical connections and leads for damage or corrosion.
3. Remove and inspect the propeller. If badly nicked, bent, or cracked, contact your Cummins MerCruiser Diesel Authorized

Repair Facility.

4. Repair nicks and corrosion damage on power package exterior finish. Contact your Cummins MerCruiser Diesel Authorized

Repair Facility.

NOTE: The engine cover contains an access panel allowing access to the engine fuse panel, the engine oil fill cap, and engine

oil dipstick without removing the entire engine cover.

Engine Cover

Removal

1. Remove the engine fuse panel cover.
2. Lift straight up and detach the engine cover from the ball stud mounts.

a -

Engine cover

b -

Fuse panel cover

c -

Engine access

3. Replace the fuse panel cover during storage.

Cleaning

1. Clean the engine cover with warm soapy water.
2. Air dry the cover.

Inspection

1. Inspect the engine cover for cracks or deterioration.
2. Inspect the rubber grommets for deterioration.
3. Inspect the hardware used with each grommet.
4. Replace damaged parts.

Installation

1. Remove the fuse panel cover.
2. Set the engine cover over the ball stud mounts.

33467

a

b

c

Содержание QSD 2.0








































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды