MerCruiser QSD 2.0 Скачать руководство пользователя

Страница: 115 / 135

Section 5 - Maintenance

90-8M0057081

eng

MARCH 2011

Page 107

5. Bend the three tabs down into the grooves.

a -

Prop

b -

Tab washer

c -

Drive sleeve adapter

d -

Tab bent down

e -

Propeller nut

Bravo Two Models

IMPORTANT: Use the correct rotation propeller. The propeller rotation MUST match the direction of rotation of the propeller shaft.
1. Liberally coat the propeller shaft spline with one of the following Quicksilver lubricants.

Tube Ref No.

Description

Where Used

Part No.

Special Lubricant 101

Propeller shaft splines

92-802865Q02

2-4-C Marine Lubricant

with Teflon

Propeller shaft splines

92-802859A 1

Anti-Corrosion Grease

Propeller shaft splines

92-802867Q 1

NOTE: Anti‑corrosion grease is for saltwater applications only.

2. Install the propeller with the attaching hardware as shown.
3. Torque the propeller nut.

Bravo Two

a -

Propeller shaft splines

b -

Forward thrust hub

c -

Propeller

d -

Spline washer

e -

Tab washer

f -

Propeller nut

NOTE: The propeller torque stated is a minimum torque value.

Description

lb–in.

lb–ft

Bravo Two propeller nut

–

Then align tabs with groves

4. Continue to tighten the propeller nut until the three tabs on the tab washer align with the grooves on the spline washer.

4750

8566

Содержание QSD 2.0








































































































































Результаты поиска

Содержание QSD 2.0

Отзывы:

Похожие инструкции для QSD 2.0

Бренды по названию

Популярные бренды

MerCruiser QSD 2.0, Руководство пользователя

Результаты поиска

Содержание QSD 2.0

Отзывы:

Похожие инструкции для QSD 2.0

Бренды по названию

Популярные бренды