
271
[Factory]
These are the setting items for factory.
Strictly for SATO authorized service personnel use.
[Wi-Fi Site Survey]
Make a survey of the wave strength for each access point and display or print the survey results.
This information is shown only when the optional wireless LAN/Bluetooth kit is installed.
The options are as follows:
SiteSurveyDisp.
Shows the wave strength for each access point.
SiteSurveyPrint
Prints the wave strength for each access point.
[Install Certificates]
Install certificates used for Wi-Fi authentication and for HTTPS.
Available only if you have connected the USB memory to the USB connector (Type A) on the back of
the product.
•
Be sure to perform a virus check on the USB memory before connecting it to the
product. SATO Corporation shall not be held responsible for any product malfunctions
caused by a virus spread via USB memory.
The setting item is as follows:
HTTPS
Installs the HTTPS certificates from the USB memory.
Wi-Fi Root CA
Installs the Wi-Fi Root CA certificates from the USB memory.
Wi-Fi Client
Installs the Wi-Fi client certificates from the USB memory.
Wi-Fi Private Key
Installs the Wi-Fi private key from the USB memory.
EAP-FAST PAC File
Installs the EAP-FAST PAC file from the USB memory.
The procedure to install the certificates and PAC files is as follows:
1. Save the certificate files to the USB memory’s root folder.
Acceptable file extensions are as follows:
Содержание CT4-LX
