
[HEX-Dump]
266
[Buffer Dump]
Save the receive buffer data to the product.
You can use this if you have disabled the [Hex Dump Mode] menu.
Tap [START] on the startup screen to save the data to the product.
Save the receive buffer data to "buff/" in the product.
•
The data files of the receive buffer are created for each type of interface.
•
The details of the file created inside "buff/" of the product are as follows:
BT0001.bin
The contents of the receive buffer for Bluetooth.
LAN0001.bin
The contents of the receive buffer for LAN.
NFC0001.bin
The contents of the receive buffer for NFC.
PIPE0001.bin
The contents of the receive buffer for pipe.
SCI0001.bin
The contents of the receive buffer for RS-232C.
USB0001.bin
The contents of the receive buffer for USB.
WIFI0001.bin
The contents of the receive buffer for wireless LAN.
•
If you perform the [Buffer Dump] again, the existing file will be overwritten.
[Log Files]
The setting items are as follows:
[Copy]
Copy the log files of the product to the USB memory.
Available only if you have connected the USB memory to the USB connector (Type A) on the back of
the product.
•
Be sure to perform a virus check on the USB memory before connecting it to the
product. SATO Corporation shall not be held responsible for any product malfunctions
caused by a virus spread via USB memory.
The procedure to copy the log files is as follows:
1. Tap the file type from the list to copy.
Содержание CT4-LX
