
135
◦
Rewind the ribbon several turns in thermal transfer mode. When the Label Waste Prevention
function is in use, backfeed returns the ribbon that has been rewound one time to the print
head. When this happens, rewinding the ribbon in advance can prevent the used ribbon from
being used to print again.
1. Open the top cover.
2. Open the ribbon unit toward the front.
3. Close the ribbon cover , turn the dial to rewind the carbon ribbon a few times .
4. Close the top cover.
•
When the Label Waste Prevention function is enabled, you do not need to tap [FEED] in Offline
mode before printing. (Regardless of whether you enable the Label Waste Prevention function or
not, tapping [FEED] feeds media to align with the print start position.)
•
Use the default value for [Finisher Feed]. If you change [Finisher Feed], operation of the Label
Waste Prevention function is not guaranteed.
•
Disable [Auto Measure]. If you enable [Auto Measure], media feeds every time auto measure is
executed, regardless of the settings for the Label Waste Prevention function.
Adjusting the Label Top Sensor
With the Label Waste Prevention function, the label top sensor, which is located at the media
discharge outlet, detects the leading edge of the media and aligns the media to the print start position.
If the print start position is misaligned, try adjusting the position and sensitivity of the label top sensor.
•
Adjusting the Position of the Sensor
[Printing] > [Advanced] > [Adjustments] > [Label Top Sensor]
•
Adjusting the Sensitivity of the Sensor
[Printing] > [Advanced] > [Calibrate] > [Auto-calibration] > [Label Top]
Содержание CT4-LX
