
[RFID]
212
•
To cancel an entire print job, open and close the top cover to switch the product to
Offline mode, and then tap [CANCEL].
[Retries]
Set the number of times the retry/release operations as set in [Retry Mode] are repeated before
printing stops and the RFID error screen opens, when an RFID error occurs.
The setting range is from 0 to 9.
[Mark bad tags]
Set whether to enable error printing when an RFID tag error occurs.
[RFID Undetected Warning]
To prevent wasting RFID tags, set whether to stop printing and display an RFID undetected warning
error if there is no RFID command in the print job.
The RFID commands that are detected by this function are EPC code write <IP0> and UID/EPC/IDm
print <TU> commands.
The options are as follows:
Disable
The RFID undetected warning error is not displayed. Printing continues.
RFID Tag
Printing stops and an RFID undetected warning error is displayed if there is no RFID command in
the print job when an RFID tag is loaded.
The error is no longer displayed if the media is replaced with normal labels.
RFID Command
Printing stops and an RFID undetected warning error is displayed if there is no RFID command in
the print job.
•
An RFID undetected warning is displayed even when using an RFID command that
is intended to be detected in the print job, if it is written in the data that caused the
command error.
[Log RFID Data]
Enable or disable the log function that records information about the written RFID data.
The log data can record up to 100 inlays of information. When the log file reaches its maximum size,
the new log data overwrites the older log data.
All the log data will be lost if the product is powered off.
[Data To Record]
Set the data to record the log when [Log RFID Data] is enabled.
The options are as follows:
Содержание CT4-LX
